Study better. Learn faster. Get the grade you want.
Discover why millions of students use us to learn better.

Sign up now and start studying this note for FREE

Chapter 3 ? Integral Relations for a Control Volume 3.1 Discuss Newton?s second law (the linear momentum relation) in these three forms: () system dd mm d dt dt ? ? ?? ???= ?= ?= ?? ? Fa F V F V Solution: These questions are just to get the students thinking about the basic laws of mechanics. They are valid and equivalent for constant-mass systems, and we can make use of all of them in certain fluids problems, e.g. the #1 form for small elements, #2 form for rocket propulsion, but the #3 form is control-volume related and thus the most popular in this chapter. 3.2 Consider the angular-momentum relation in the form () O system d d dt ? ? ? ? ?= ×? ? ? ? ? ? ? MrV What does r mean in this relation? Is this relation valid in both solid and fluid mechanics? Is it related to the linear-momentum equation (Prob. 3.1)? In what manner? Solution: These questions are just to get the students thinking about angular momentum versus linear momentum. One might forget that r is the position vector from the moment-center O to the elements ? d? where momentum is being summed. Perhaps rO is a better notation. 3.3 For steady laminar flow through a long tube (see Prob. 1.12), the axial velocity distribution is given by u = C(R 2 ? r 2 ), where R is the tube outer radius and C is a constant. Integrate u(r) to find the total volume flow Q through the tube. Solution: The area element for this axisymmetric flow is dA = 2? r dr. From Eq. (3.7), 22 0 ()2 . R Q u dA C R r r dr Ans?==? = ?? ? 4 CR 2 Chapter 3 ? Integral Relations for a Control Volume 177 P3.4 A fire hose has a 5-inch inside diameter and is flowing at 600 gal/min. The flow exits through a nozzle contraction at a diameter D n . For steady flow, what should D n be, in inches, to create an exit velocity of 25 m/s? Solution: This is a straightforward one-dimensional steady-flow continuity problem. Some unit conversions are needed: 600 gal/min = 1.337 ft 3 /s; 25 m/s = 82.02 ft/s ; 5 inches = 0.4167 ft The hose diameter (5 in) would establish a hose average velocity of 9.8 ft/s, but we don?t really need this. Go directly to the volume flow: 3.5 A theory proposed by S. I. Pai in 1953 gives the following velocity values u(r) for turbulent (high-Reynolds number) airflow in a 4-cm-diameter tube: r, cm 0 0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0 u, m/s 6.00 5.97 5.88 5.72 5.51 5.23 4.89 4.43 0.00 Comment on these data vis-a-vis laminar flow, Prob. 3.3. Estimate, as best you can, the total volume flow Q through the tube, in m 3 /s. Solution: The data can be plotted in the figure below. .144.0forSolve;)02.82( 4 337.1 22 3 AnsftD s ft DVA s ft Q nnnn in1.73===== ? Solutions Manual ? Fluid Mechanics, Fifth Edition 178 As seen in the figure, the flat (turbulent) velocities do not resemble the parabolic laminar- flow profile of Prob. 3.3. (The discontinuity at r = 1.75 cm is an artifact?we need more data for 1.75 < r < 2.0 cm.) The volume flow, Q = ? u(2? r)dr, can be estimated by a numerical quadrature formula such as Simpson?s rule. Here there are nine data points: 11 22 33 44 55 66 77 88 99 2( 4 2 4 2 4 2 4 ) 3 ,. r Q rururururururururu For the given data Q Ans ? ? ?? =++++++++ ?? ?? ? 3 0.0059 m /s 3.6 When a gravity-driven liquid jet issues from a slot in a tank, as in Fig. P3.6, an approximation for the exit velocity distribution is 2( ),ughz?? where h is the depth of the jet centerline. Near the slot, the jet is horizontal, two-dimensional, and of thickness 2L, as shown. Find a general expression for the total volume flow Q issuing from the slot; then take the limit of your result if .Lh Fig. P3.6 Solution: Let the slot width be b into the paper. Then the volume flow from Eq. (3.7) is +L 1/2 L Q udA [2g(h z)] bdz .Ans ? == ? =? ?? 3/2 3/2 2b (2g)[(h L) (h L) ] 3 +?? In the limit of L h, this formula reduces to .AnsQ (2Lb) (2gh)? _______________________________________________________________________ P3.7 A spherical tank, of diameter 35 cm, is leaking air through a 5-mm-diameter hole in its side. The air exits the hole at 360 m/s and a density of 2.5 kg/m 3 . Assuming uniform mixing, (a) find a formula for the rate of change of average density in the tank; and (b) calculate a numerical value for (d?/dt) in the tank for the given data. Solution: If the control volume surrounds the tank and cuts through the exit flow, (b) For the given data, we calculate ).( )( )(foSolve )()()(0| tank tank tanktanktanktank aAns AV dt d r AV dt d m dt d dt dm out outoutsystem ? ? ? ????? ?= +=+== Chapter 3 ? Integral Relations for a Control Volume 179 3.8 Three pipes steadily deliver water at 20°C to a large exit pipe in Fig. P3.8. The velocity V2 = 5 m/s, and the exit flow rate Q4 = 120 m 3 /h. Find (a) V1; (b) V3; and (c) V4 if it is known that increasing Q3 by 20% would increase Q4 by 10%. Solution: (a) For steady flow we have Q1 + Q2 + Q3 = Q4, or Fig. P3.8 11 2 2 33 4 4 VA VA VA VA+ += (1) Since 0.2Q3 = 0.1Q4, and Q4 = (120 m 3 /h)(h/3600 s) = 0.0333 m 3 /s, 3 4 3 2 3 (0.0333 m /s) (b) 2 (0.06 ) 2 Q ns. A ? == =5.89 m/s Substituting into (1), 22 2 1 (0.04 ) (5) (0.05 ) (5.89) (0.06 ) 0.0333 (a) 44 4 VA ?? ? ?? ?? ?? ++ = ?? ?? ?? ?? ?? ?? 1 V5.45 m/s= From mass conservation, Q4 = V4A4 32 4 (0.0333 m /s) V ( )(0.06 )/4 (c)Ans.?= 4 V5.24 m/s= ).( )35.0)(6/( )/360]()005.0)(4/)[(/5.2( 3 23 tank bAns m smmmkg dt d s kg/m 0.79 3 ?== ? ? ?? Solutions Manual ? Fluid Mechanics, Fifth Edition 180 3.9 A laboratory test tank contains seawater of salinity S and density ?. Water enters the tank at conditions (S1, ?1, A1, V1) and is assumed to mix immediately in the tank. Tank water leaves through an outlet A2 at velocity V2. If salt is a ?conservative? property (neither created nor destroyed), use the Reynolds transport theorem to find an expression for the rate of change of salt mass Msalt within the tank. Solution: By definition, salinity S = ?salt/?. Since salt is a ?conservative? substance (not consumed or created in this problem), the appropriate control volume relation is 21 salt system s 1 CV dM d dSmSm0 dt dt ?? ?? =+?= ?? ?? | ? or: Ans. s CV 1 1 1 1 2 2 dM SAVSAV dt =?| ?? 3.10 Water flowing through an 8-cm-diameter pipe enters a porous section, as in Fig. P3.10, which allows a uniform radial velocity vw through the wall surfaces for a distance of 1.2 m. If the entrance average velocity V1 is 12 m/s, find the exit velocity V2 if (a) vw = 15 cm/s out of the pipe walls; (b) vw = 10 cm/s into the pipe. (c) What value of vw will make V2 = 9 m/s? Fig. P3.10 Solution: (a) For a suction velocity of vw = 0.15 m/s, and a cylindrical suction surface area, 2 w A 2 (0.04)(1.2) 0.3016 m?== 1w2 QQ Q= + 22 2 (12)( )(0.08 )/4 (0.15)(0.3016) V ( )(0.08 )/4 (a)Ans.??=+ 2 V3 m/s= (b) For a smaller wall velocity, vw = 0.10 m/s, Chapter 3 ? Integral Relations for a Control Volume 181 22 2 (12)( )(0.08 )/4 (0.10)(0.3016) V ( )(0.08 )/4 (b)Ans.??=+ 2 V6 m/s= (c) Setting the outflow V2 to 9 m/s, the wall suction velocity is, w (12)( )(0.08 )/4 (v )(0.3016) (9)( )(0.08 )/4 =+ w v0.05 m/s5 cm/s==out 3.11 A room contains dust at uniform concentration C = ?dust/?. It is to be cleaned by introducing fresh air at an inlet section Ai, Vi and exhausting the room air through an outlet section. Find an expression for the rate of change of dust mass in the room. Solution: This problem is very similar to Prob. 3.9 on the previous page, except that here Ci = 0 (dustfree air). Refer to the figure in Prob. 3.9. The dust mass relation is dust system dust out out in in CV dM d 0dCmCm, dt dt ?? ?? == + ? ?? ?? | ? dust in CV dM or, since C 0, we obtain . dt Ans?| ? oo CAV To complete the analysis, we would need to make an overall fluid mass balance. 3.12 The pipe flow in Fig. P3.12 fills a cylindrical tank as shown. At time t = 0, the water depth in the tank is 30 cm. Estimate the time required to fill the remainder of the tank. Fig. P3.12 Solution: For a control volume enclosing the tank and the portion of the pipe below the tank, 0 out in d dv m m dt ? ?? + ?= ?? ? 2 ()()0 out in dh RAVAV dt ?? ? ?+ ?= Solutions Manual ? Fluid Mechanics, Fifth Edition 182 2 2 4 998 (0.12 )(2.5 1.9) 0.0153 / , 4998( )(0.75 ) 0.7/0.0153 dh ms dt Ans. t ? ? ???? =?= ?? ?? ?? ?? ?= = 46 s Chapter 3 ? Integral Relations for a Control Volume 183 P3.13 The cylindrical container in Fig. P3.13 is 20 cm in diameter and has a conical contraction at the bottom with an exit hole 3 cm in diameter. The tank contains fresh water at standard sea-level conditions. If the water surface is falling at the nearly steady rate dh/dt ? ?0.072 m/s, estimate the average velocity V from the bottom exit. Solution: We could simply note that dh/dt is the same as the water velocity at the surface and use Q 1 = Q 2 , or, more instructive, approach it as a control volume problem. Let the control volume encompass the entire container. Then the mass relation is 3.14 The open tank in the figure contains water at 20°C. For incompressible flow, (a) derive an analytic expression for dh/dt in terms of (Q1, Q2, Q3). (b) If h is constant, determine V2 for the given data if V1 = 3 m/s and Q3 = 0.01 m 3 /s. Solution: For a control volume enclosing the tank, 2 213 213 () (), 4 CV dddh dQQQ QQQ dt dt ? ?? ? ? ? ?? +??= +?? ?? ?? ? . (a)solve Ans 132 2 QQQdh dt (d/4) + ? = ? h(t) V ? Fig. P3.13 D .)]072.0([) 3 20 (:datatheIntroduce )()(: 4 Cancel0 44 :or , 4 |) 4 ()(0| 2 222 22 Ans s m cm cm V dt dh D D VVD dt dh D VDhD dt d md dt d dt dm exit exit exitcone CV outsystem s m 3.2=??= ?==+ ++=+== ? ? ? ? ? ? ? ? ? ? ???? Solutions Manual ? Fluid Mechanics, Fifth Edition 184 If h is constant, then 22 213 2 0.01 (0.05) (3.0) 0.0159 (0.07) , 44 QQQ V ? ? =+= + = = 2 . (b)solve AnsV4.13 m/s= Chapter 3 ? Integral Relations for a Control Volume 185 3.15 Water flows steadily through the round pipe in the figure. The entrance velocity is Vo. The exit velocity approximates turbulent flow, u = umax(1 ? r/R) 1/7 . Determine the ratio Uo/umax for this incompressible flow. Solution: Inlet and outlet flow must balance: 1/7 22 12 00 49 ,2 12, 60 RR omax omax r :Q Q or U r dr u r dr or: U R u R R ? ??? ?? ==? = ?? ?? ?? Cancel and rearrange for this assumed incompressible pipe flow: max . o U Ans u = 49 60 3.16 An incompressible fluid flows past an impermeable flat plate, as in Fig. P3.16, with a uniform inlet profile u = Uo and a cubic polynomial exit profile 3 o 3 where 2 y uU ?? ? ? ?? ? ?= ?? ?? Fig. P3.16 Compute the volume flow Q across the top surface of the control volume. Solution: For the given control volume and incompressible flow, we obtain 3 top right left o o 3 00 3 0Q Q Q Q U bdy Ubdy 2 2 yy ?? ? ? ?? =+ ?=+ ? ? ?? ?? ?? oo 5 QUbUb,solve for . 8 Ans??=+ ? o 3 QUb 8 = ? 3.17 Incompressible steady flow in the inlet between parallel plates in Fig. P3.17 is uniform, u = Uo = 8 cm/s, while downstream the flow develops into the parabolic laminar profile u = az(zo ? z), where a is a constant. If zo = 4 cm and the fluid is SAE 30 oil at 20°C, what is the value of umax in cm/s? Fig. P3.17 Solutions Manual ? Fluid Mechanics, Fifth Edition 186 Solution: Let b be the plate width into the paper. Let the control volume enclose the inlet and outlet. The walls are solid, so no flow through the wall. For incompressible flow, oo zz 32 out in o o o o o o o 00 0 Q Q az(z z)bdz U bdz abz /6 U bz 0, or: a 6U /z=?= ? ? = ? = = ?? Thus continuity forces the constant a to have a particular value. Meanwhile, a is also related to the maximum velocity, which occurs at the center of the parabolic profile: 222oo omax o ooo zz At z z /2: u u a z az /4 (6U /z )(z /4) 22 ??? ? === ?== ??? ? ??? ? max o 33 or: u U (8 cm/s) . 22 Ans== = cm 12 s Note that the result is independent of zo or of the particular fluid, which is SAE 30 oil. 3.18 An incompressible fluid flows steadily through the rectangular duct in the figure. The exit velocity profile is given by u ? umax(1 ? y 2 /b 2 )(1 ? z 2 /h 2 ). (a) Does this profile satisfy the correct boundary conditions for viscous fluid flow? (b) Find an analytical expression for the volume flow Q at the exit. (c) If the inlet flow is 300 ft 3 /min, estimate umax in m/s. Solution: (a) The fluid should not slip at any of the duct surfaces, which are defined by y = ±b and z = ±h. From our formula, we see u ? 0 at all duct surfaces, OK. Ans. (a) (b) The exit volume flow Q is defined by the integral of u over the exit plane area: 22 max max 22 44 11 33 hb hb y zbh QudA u dydzu bh ++ ?? ???? ???? == ?? = ???? ???? ???? ???? ?? ? ? . ( )bAns= max 16bhu 9 (c) Given Q = 300 ft 3 /min = 0.1416 m 3 /s and b = h = 10 cm, the maximum exit velocity is 3 max m16 0.1416 (0.1 m)(0.1 m) , . (c) s9 Qusolve frAns== max u7.96 m/s= Chapter 3 ? Integral Relations for a Control Volume 187 3.19 Water from a storm drain flows over an outfall onto a porous bed which absorbs the water at a uniform vertical velocity of 8 mm/s, as shown in Fig. P3.19. The system is 5 m deep into the paper. Find the length L of bed which will completely absorb the storm water. Fig. P3.19 Solution: For the bed to completely absorb the water, the flow rate over the outfall must equal that into the porous bed, 1PB Q Q ; or (2 m/s)(0.2 m)(5 m) (0.008 m/s)(5 m)L Ans.==L50m? 3.20 Oil (SG-0.91) enters the thrust bearing at 250 N/hr and exits radially through the narrow clearance between thrust plates. Compute (a) the outlet volume flow in mL/s, and (b) the average outlet velocity in cm/s. Solution: The specific weight of the oil is (0.91)(9790) = 8909 N/m 3 . Then Fig. P3.20 3 6 21 3 250/3600 N/s m QQ 7.810 . (a) s8909 N/m Ans ? == =× = mL 7.8 s 6 22 2 But also Q V (0.1 m)(0.002 m) 7.8 10 , solve for V . (b)Ans? ? = cm 1.24 s ________________________________________________________________________ Solutions Manual ? Fluid Mechanics, Fifth Edition 188 P3.21 Modify Prob. 3.13 as follows. Let the plate be L = 125? long from inlet to exit. The plate is porous and is drawing in fluid from the boundary layer at a uniform suction velocity v w . (a) Calculate Q across the top if v w = 0.002U o . (b) Find the ratio v w /U o for which Q across the top is zero. Solution: The situation is now as shown at right. The inlet and outlet flows were calculated in Prob. P3.13. The wall flow is the suction velocity times the wall area: Q wall = v w L b = v w (125?) b The total volume flow through the control volume is zero, solve for Q: (a) If v w = 0.002U o , compute Q = (1/8) ?bU o Ans.(a) (b) Q = 0 when v w = 0.003U o . Ans.(b) 3.22 The converging-diverging nozzle shown in Fig. P3.22 expands and accelerates dry air to supersonic speeds at the exit, where p2 = 8 kPa and T2 = 240 K. At the throat, p1 = 284 kPa, T1 = 665 K, and V1 = 517 m/s. For steady compressible flow of an ideal gas, estimate (a) the mass flow in kg/h, (b) the velocity V2, and (c) the Mach number Ma2. Fig. P3.22 Solution: The mass flow is given by the throat conditions: 2 111 3 284000 kg m m A V (0.01 m) 517 . (a) (287)(665) 4 sm Ans ? ? ???? == = ?? ?? ???? kg 0.0604 s For steady flow, this must equal the mass flow at the exit: Q 5U o b?/8 U o b? Q wall control volume L = 125 ? ????? bvbUbvbUbUQ wowoo 125 8 3 125 8 5 ?=??= Chapter 3 ? Integral Relations for a Control Volume 189 2 222 2 2 kg 8000 0.0604 A V (0.025) V , or V . (b) s 287(240) 4 Ans ? ? ?? == ? ?? ?? m 1060 s Recall from Eq. (1.39) that the speed of sound of an ideal gas = (kRT) 1/2 . Then 22 1/2 1060 Ma = V /a = [1.4(287)(240)] Mach number at exit: . (c)Ans? 3.41 3.23 The hypodermic needle in the figure contains a liquid (SG = 1.05). If the serum is to be injected steadily at 6 cm 3 /s, how fast should the plunger be advanced (a) if leakage in the plunger clearance is neglected; and (b) if leakage is 10 percent of the needle flow? Solutions Manual ? Fluid Mechanics, Fifth Edition 190 Solution: (a) For incompressible flow, the volume flow is the same at piston and exit: 33 2 11 1 6 0.366 (0.75 ) , . (a) 4 piston cm in QAVinVsoveVAns ss ? == == = in 0.83 s (b) If there is 10% leakage, the piston must deliver both needle flow and leakage: 33 2 11 1 6 0.1(6) 6.6 0.403 (0.75) , 4 needle clearance cm in AV Q Q V ss ? =+ =+= = = 1 . (b)VAns= in 0.91 s 3.24 Water enters the bottom of the cone in the figure at a uniformly increasing average velocity V = Kt. If d is very small, derive an analytic formula for the water surface rise h(t), assuming h = 0 at t = 0. Solution: For a control volume around the cone, the mass relation becomes () 22 0(tan) 34 in dd dm h h dKt dt dt ?? ?? ? ? ? ?? ?== ? ?? ?? ? 32 22 :tan 38 Integrate h d Kt ?? ???= .Solve for Ans ?? ?? ?? 1/3 22 2 3 h(t) Kt d cot 8 ?= 3.25 As will be discussed in Chaps. 7 and 8, the flow of a stream Uo past a blunt flat plate creates a broad low-velocity wake behind the plate. A simple model is given in Fig. P3.25, with only half of the flow shown due to symmetry. The velocity profile behind the plate is idealized as ?dead air? (near-zero velocity) behind the plate, plus a higher Chapter 3 ? Integral Relations for a Control Volume 191 velocity, decaying vertically above the wake according to the variation u ? Uo + ?Ue ?z/L , where L is the plate height and z = 0 is the top of the wake. Find ?U as a function of stream speed Uo. Fig. P3.25 Solution: For a control volume enclosing the upper half of the plate and the section where the exponential profile applies, extending upward to a large distance H such that exp(?H/L) ? 0, we must have inlet and outlet volume flows the same: HH z/L in o out o o o L/2 0 L Q U dz Q (U U e )dz, or: U H U H UL 2 ? ? ?? ===+? +=+? ?? ?? ?? o Cancel U H and solve for U .Ans?? o 1 U 2 3.26 A thin layer of liquid, draining from an inclined plane, as in the figure, will have a laminar velocity profile u = Uo(2y/h ? y 2 /h 2 ), where Uo is the surface velocity. If the plane has width b into the paper, (a) deter- mine the volume rate of flow of the film. (b) Suppose that h = 0.5 in and the flow rate per foot of channel width is 1.25 gal/min. Estimate Uo in ft/s. Solution: (a) The total volume flow is computed by integration over the flow area: 2 2 0 2 . (a) h no yy Q V dA U b dy Ans h h ?? == ? = ?? ?? ?? o 2 Ubh 3 (b) Evaluate the above expression for the given data: 3 22 0.5 1.25 0.002785 (1.0 ) , min 3 3 12 oo gal ft QUbUft s ?? == == ?? ?? . (b) o solve for U Ans= ft 0.10 s Solutions Manual ? Fluid Mechanics, Fifth Edition 192 P3.27 Consider a highly pressurized air tank at conditions (p o , ? o , T o ) and volume ? o . In Chap. 9 we will learn that, if the tank is allowed to exhaust to the atmosphere through a well-designed converging nozzle of exit area A, the outgoing mass flow rate will be This rate persists as long as p o is at least twice as large as the atmospheric pressure. Assuming constant T o and an ideal gas, (a) derive a formula for the change of density ? o (t) within the tank. (b) Analyze the time ?t required for the density to decrease by 25%. Solution: First convert the formula to reflect tank density instead of pressure: (a) Now apply a mass balance to a control volume surrounding the tank: (b) If the density drops by 25%, then we compute airfor685.0where, ?= ? ? o o RT Ap m oo o oo o o RTA RT ART RT Ap m ?? ??? === )( ).()(exp:2stateto1statefromIntegrate :variablesSeparate )(0| ][ 12 1 2 aAnstt RTA dtRTA d RTA dt d m dt d dt dm o o o o o o o oo o ooutoosystem ? ? = ?= +=+== ? ? ? ? ? ? ? ?? ? ??? ).( 288.0 Thus;288.0)75.0ln()( 12 bAns RTA ttt RTA o o o o ? ? ? ? =?=?=? Chapter 3 ? Integral Relations for a Control Volume 193 3.28 According to Torricelli?s theorem, the velocity of a fluid draining from a hole in a tank is V ? (2gh) 1/2 , where h is the depth of water above the hole, as in Fig. P3.28. Let the hole have area Ao and the cylindrical tank have bottom area Ab. Derive a formula for the time to drain the tank from an initial depth ho. Fig. P3.28 Solution: For a control volume around the tank, +=0 out d dv m dt ? ?? ?? ? == 2 b out o dh A mAgh dt ???? = ?? 0 0 2 ;. o t o b h Agdh dt Ans A h bo o Ah t Ag = 2 Solutions Manual ? Fluid Mechanics, Fifth Edition 194 3.29 In elementary compressible-flow theory (Chap. 9), compressed air will exhaust from a small hole in a tank at the mass flow rate ,mC?? where ? is the air density in the tank and C is a constant. If ?o is the initial density in a tank of volume v, derive a formula for the density change ?(t) after the hole is opened. Apply your formula to the following case: a spherical tank of diameter 50 cm, with initial pressure 300 kPa and temperature 100°C, and a hole whose initial exhaust rate is 0.01 kg/s. Find the time required for the tank density to drop by 50 percent. Solution: For a control volume enclosing the tank and the exit jet, we obtain ( ) out out dd 0dm,or: mC, dt dt vv ? ? ?=+ =?=? ? o t o 0 dC or: dt, or: .Ans v ? ? ?? ?? =? ? ? ?? ?? ?? C exp t v Now apply this formula to the given data. If po = 300 kPa and To = 100°C = 373°K, then ?o = p/RT = (300,000)/[287(373)] ? 2.80 kg/m 3 . This establishes the constant ?C?: ? ?? == = ? ?? ?? 3 oo 3 kg kg m m C 0.01 C 2.80 , or C 0.00357 for this hole. ssm The tank volume is 333 ( /6)D ( /6)(0.5 m) 0.00654 m .v ??== ? Then we require o 0.00357 /0.5exp tift . 0.00654 Ans?? ?? == ? ? ?? ?? 1.3 s P3.30 A steady two-dimensional water jet, 4 cm thick with a weight flow rate of 1960 N/s, strikes an angled barrier as in Fig. P3.30. Pressure and water velocity are constant everywhere. Thirty percent of the jet passes through the slot. The rest splits Fig. P3.30 1960 N/s 4 cm 35° 35° F 30% (1) (2) (3) (4) CV Chapter 3 ? Integral Relations for a Control Volume 195 symmetrically along the barrier. Calculate the horizontal force F needed, per unit thickness into the paper, to hold the barrier stationary. Solution: For water take ? = 998 kg/m. The control volume (see figure) cuts through all four jets, which are numbered. The velocity of all jets follows from the weight flow at (1): Then the x-momentum relation for this control volume yields 3.31 A bellows may be modeled as a deforming wedge-shaped volume as in Fig. P3.31. The check valve on the left (pleated) end is closed during the stroke. If b is the bellows width into the paper, derive an expression for outlet mass flow o m as a function of stroke ?(t). Solution: For a control volume enclosing the bellows and the outlet flow, we obtain Fig. P3.31 2 out d ( ) m 0, where bhL bL tan dt ????+= == 2 o d since L is constant, solve for m ( bL tan ) . dt Ans??=? =? ? ?? 22 d bL sec dt ms kg mm ms kg mm ms kg sN msN g w m s m mmmkgsm sN gA w VV ? == ? == ? = ? == ==== 70;603.0;200 /81.9 /1960 0.5 )1)(04.0)(/998)(/81.9( /1960 4312 2 1 1 32 1 1 14,3,2,1 ? .widthofmeterper3002012011000 :or,)0.5(200)55cos0.5)(70()55cos0.5)(70()0.5)(60( 11443322 AnsF F umumumumFF x N1100??++= ??+?+=? =?++=?=? D D Solutions Manual ? Fluid Mechanics, Fifth Edition 196 3.32 Water at 20°C flows through the piping junction in the figure, entering section 1 at 20 gal/min. The average velocity at section 2 is 2.5 m/s. A portion of the flow is diverted through the showerhead, which contains 100 holes of 1-mm diameter. Assuming uniform shower flow, estimate the exit velocity from the showerhead jets. Solution: A control volume around sections (1, 2, 3) yields 3 123 Q Q Q 20 gal/min 0.001262 m /s.=+= = Meanwhile, with V2 = 2.5 m/s known, we can calculate Q2 and then Q3: 3 2 222 m (2.5 m) (0.02 m) 0.000785 , 4s QVA ? == = 3 312 m 0.001262 0.000785 0.000476 s hence Q Q Q=?= ? = 3 2 3 m /100 0.00000476 (0.001) , s4 . jet jet Each hole carries Q V solve V Ans ? == = m 6.06 s 3.33 In some wind tunnels the test section is perforated to suck out fluid and provide a thin viscous boundary layer. The test section wall in Fig. P3.33 contains 1200 holes of 5-mm diameter each per square meter of wall area. The suction velocity through each hole is Vr = 8 m/s, and the test-section entrance velocity is V1 = 35 m/s. Assuming incompressible steady flow of air at 20°C, compute (a) Vo, (b) V2, and (c) Vf, in m/s. Fig. P3.33 Solution: The test section wall area is (?)(0.8 m)(4 m) = 10.053 m 2 , hence the total number of holes is (1200)(10.053) = 12064 holes. The total suction flow leaving is 23 suction hole Q NQ (12064)( /4)(0.005 m) (8 m/s) 1.895 m /s?== ? 22 oo1 o o (a) Find V : Q Q or V (2.5) (35) (0.8) , 44 solve for V . (a)Ans ? ? == ? m 3.58 s 22 21suction 2 2 (b) Q Q Q (35) (0.8) 1.895 V (0.8) , 44 or: V . (b)Ans ? ? =? = ? = ? m 31.2 s 22 ff2 f f (c) Find V : Q Q or V (2.2) (31.2) (0.8) , 44 solve for V . (c)Ans ? ? == ? m 4.13 s Solutions Manual ? Fluid Mechanics, Fifth Edition 198 3.34 A rocket motor is operating steadily, as shown in Fig. P3.34. The products of combustion flowing out the exhaust nozzle approximate a perfect gas with a molecular weight of 28. For the given conditions calculate V2 in ft/s. Solution: Exit gas: Molecular weight = 28, thus Rgas = 49700/28 = 1775 ft 2 /(s 2 ?°R). Then, Fig. P3.34 2 exit gas p 15(144) psf 0.000780 slug/ft RT (1775)(1100 460) ? == ? + For mass conservation, the exit mass flow must equal fuel + oxygen entering = 0.6 slug/s: ? ? ?? === ? ?? ?? 2 exit e e e e e slug 5.5 m 0.6 A V (0.00078) V , solve for V . s41 Ans ft 4660 s 3.35 In contrast to the liquid rocket in Fig. P3.34, the solid-propellant rocket in Fig. P3.35 is self-contained and has no entrance ducts. Using a control-volume analysis for the conditions shown in Fig. P3.35, compute the rate of mass loss of the propellant, assuming that the exit gas has a molecular weight of 28. Fig. P3.35 Solution: With M = 28, R = 8313/28 =297 m 2 /(s 2 ?K), hence the exit gas density is 3 exit p 90,000 Pa 0.404 kg/m RT (297)(750 K) ? == = For a control volume enclosing the rocket engine and the outlet flow, we obtain CV out d (m ) m 0, dt + = 2 propellant exit e e e d or: (m ) m A V (0.404)( /4)(0.18) (1150) . dt Ans??=? =? =? ? ? kg 11.8 s Chapter 3 ? Integral Relations for a Control Volume 199 Solutions Manual ? Fluid Mechanics, Fifth Edition 200 3.36 The jet pump in Fig. P3.36 injects water at U1 = 40 m/s through a 3-in pipe and entrains a secondary flow of water U2 = 3 m/s in the annular region around the small pipe. The two flows become fully mixed down-stream, where U3 is approximately constant. For steady incompressible flow, compute U3 in m/s. Solution: First modify the units: D1 = 3 in = 0.0762 m, D2 = 10 in = 0.254 m. For incompressible flow, the volume flows at inlet and exit must match: 2222 12 3 3 Q Q Q , or: (0.0762) (40) [(0.254) (0.0762) ](3) (0.254) U 44 4 ?? ? += + ? = Solve for .Ans 3 U6.3 m/s? 3.37 A solid steel cylinder, 4.5 cm in diameter and 12 cm long, with a mass of 1500 grams, falls concentrically through a 5-cm-diameter vertical container filled with oil (SG = 0.89). Assuming the oil is incom- pressible, estimate the oil average velocity in the annular clearance between cylinder and container (a) relative to the container; and (b) relative to the cylinder. Solution: (a) The fixed CV shown is relative to the container, thus: 222 ,: ( ), . (a) 44 cyl oil cyl oil Q Q or d V D d V thus Ans ?? ==? 2 oil cyl 22 d VV Dd = ? For the given dimensions (d = 4.5 cm and D = 5.0 cm), Voil = 4.26 Vcylinder. (b) If the CV moves with the cylinder we obtain, relative to the cylinder, =+= () . (b) oil relative to cylinder part a cyl cyl VVV VAns 2 cyl 22 D V5.26 Dd ? ? Chapter 3 ? Integral Relations for a Control Volume 201 3.38 An incompressible fluid is squeezed between two disks by downward motion Vo of the upper disk. Assuming 1-dimensional radial outflow, find the velocity V(r). Solution: Let the CV enclose the disks and have an upper surface moving down at speed Vo. There is no inflow. Thus Fig. P3.38 2 out CV CS dd d V dA 0 ( r h) 2 rh V, dt dt ?? ? ?? ?? ?? +==+ ?? ?? ?? 2 o dh dh or: r 2rhV 0, but V (the disk velocity) dt dt += =? As the disk spacing drops, h(t) ? ho ? Vot, the outlet velocity is V = Vor/(2h). Ans. 3.39 A wedge splits a sheet of 20°C water, as shown in Fig. P3.39. Both wedge and sheet are very long into the paper. If the force required to hold the wedge stationary is F = 126 N per meter of depth into the paper, what is the angle ? of the wedge? F 6 m/s 4 cm 6 m/s 6 m/sFig. P3.39 ? Solutions Manual ? Fluid Mechanics, Fifth Edition 202 Solution: For water take ? = 998 kg/m 3 . First compute the mass flow per unit depth: The mass flow (and velocity) are the same entering and leaving. Let the control volume surround the wedge. Then the x-momentum integral relation becomes 3.40 The water jet in Fig. P3.40 strikes normal to a fixed plate. Neglect gravity and friction, and compute the force F in newtons required to hold the plate fixed. Solution: For a CV enclosing the plate and the impinging jet, we obtain: x up up down down j j jj j j j FFm mu mu mu, m AV? ?=?= + ? =? = Fig. P3.40 222 jj Thus F A V (998) (0.05) (8) .Ans??== ??500 N 3.41 In Fig. P3.41 the vane turns the water jet completely around. Find the maximum jet velocity Vo for a force Fo. Solution: For a CV enclosing the vane and the inlet and outlet jets, Fig. P3.41 ?=?= ? = ?? + x o out out in in jet o jet o FFmumum(V)m(V) 3 / (998 / )(6 / )(0.04 ) 239.5 /m b Vh kg m m s m kg s m?== = ? ()(cos)(cos1) 22 : 124 / (239.5 / )(6 / )(cos 1) 2 Solve cos 0.9137 , 24 , . 22 x out in o FFmuumV VmV or N m kg s m m s Ans ? ? ? ?? ? ?=?= ? = ?= ? ?= ? ? === o 48 Chapter 3 ? Integral Relations for a Control Volume 203 2 oooo o or: F 2 A V , solve for V Ans.?== o 2 oo F 2(/4)D?? 3.42 A liquid of density ? flows through the sudden contraction in Fig. P3.42 and exits to the atmosphere. Assume uniform conditions (p1, V1, D1) at section 1 and (p2, V2, D2) at section 2. Find an expression for the force F exerted by the fluid on the contraction. Fig. P3.42 Solution: Since the flow exits directly to the atmosphere, the exit pressure equals atmospheric: p2 = pa. Let the CV enclose sections 1 and 2, as shown. Use our trick (page 129 of the text) of subtracting pa everywhere, so that the only non-zero pressure on the CS is at section 1, p = p1 ? pa. Then write the linear momentum relation with x to the right: x1a121 2111 FF(pp)Amumu,wheremm AV??=?? = ? = = 22 11 on fluid1a111121 But u V and u V . Solve for F (p p )A A V ( V V )?=? =? = ? + ? + Meanwhile, from continuity, we can relate the two velocities: 22 2 1 2 11 22 2 1 1 2 Q Q , or ( /4)D V ( /4)D V , or: V V (D /D )??=== Finally, the force of the fluid on the wall is equal and opposite to Fon fluid, to the left: () 222 2 fluid on wall 1 a 1 1 1 1 1 2 1 1 F(pp)AAVDD1,AD. 4 Ans ? ? ?? =? ? ? = ?? The pressure term is larger than the momentum term, thus F > 0 and acts to the left. 3.43 Water at 20°C flows through a 5-cm-diameter pipe which has a 180° vertical bend, as in Fig. P3.43. The total length of pipe between flanges 1 and 2 is 75 cm. When the weight flow rate is 230 N/s, p1 = 165 kPa, and p2 = 134 kPa. Neglecting pipe weight, determine the total force which the flanges must withstand for this flow. Fig. P3.43 Solution: Let the CV cut through the flanges and surround the pipe bend. The mass flow rate is (230 N/s)/(9.81 m/s 2 ) = 23.45 kg/s. The volume flow rate is Q = 230/9790 = 0.0235 m 3 /s. Then the pipe inlet and exit velocities are the same magnitude: 3 12 2 0.0235 m /s m V V V Q/A 12.0 s( /4)(0.05 m)? === = ? Subtract pa everywhere, so only p1 and p2 are non-zero. The horizontal force balance is: xx,flange 1a1 2a2 22 11 22 x,fl FF (pp)A(pp)Amumu F (64000) (0.05) (33000) (0.05) (23.45)( 12.0 12.0 m/s) 44 ?? ?= +? + ? = ? =+ + = ?? x,flange or: F 126 65 561 .Ans=? ? ? ? 750 N? The total x-directed force on the flanges acts to the left. The vertical force balance is 2 y y,flange pipe fluid F F W W 0 (9790) (0.05) (0.75) . 4 Ans ? ?= = + =+ ?14 N Clearly the fluid weight is pretty small. The largest force is due to the 180° turn. 3.44 Consider uniform flow past a cylinder with a V-shaped wake, as shown. Pressures at (1) and (2) are equal. Let b be the width into the paper. Find a formula for the force F on the cylinder due to the flow. Also compute CD = F/(?U 2 Lb). Fig. P3.44 Solution: The proper CV is the entrance (1) and exit (2) plus streamlines above and below which hit the top and bottom of the wake, as shown. Then steady-flow continuity yields, L 21 0 Uy 0 u dA u dA 2 1 b dy 2 UbH, 2L ?? ? ? ?? =?= +? ?? ?? ?? ? Chapter 3 ? Integral Relations for a Control Volume 205 where 2H is the inlet height. Solve for H = 3L/4. Now the linear momentum relation is used. Note that the drag force F is to the right (force of the fluid on the body) thus the force F of the body on fluid is to the left. We obtain, L 2 x drag 21 0 UyUy F 0 u u dA u u dA 2 1 1 bdy 2H U b F 2L2L ?? ? ? ???? ?== ? = + + ? =? ???? ???? ?? ? 22 drag 3L 3 7 Use H , then F U Lb U Lb . 426 Ans??==?? 2 1 ULb 3 ? The dimensionless force, or drag coefficient F/(?U 2 Lb), equals CD = 1/3. Ans. Solutions Manual ? Fluid Mechanics, Fifth Edition 206 P3.45 A 12-cm-diameter pipe, containing water flowing at 200 N/s, is capped by an orifice plate, as in Fig. P3.45. The exit jet is 25 mm in diameter. The pressure in the pipe at section 1 is 800 kPa-gage. Calculate the force F required to hold the orifice plate. Solution: For water take ? = 998 kg/m 3 . This is a straightforward x-momentum problem. First evaluate the mass flow and the two velocities: Now apply the x-momentum relation for a control volume surrounding the plate: 3.46 When a jet strikes an inclined plate, it breaks into two jets of equal velocity V but unequal fluxes ?Q at (2) and (1 ? ?)Q at (3), as shown. Find ?, assuming that the tangential force on the plate is zero. Why doesn?t the result depend upon the properties of the jet flow? Fig. P3.46 1 V 2 200 N/s F ? Fig. P3.45 d = 25 mm s m mmkg skg A m V s m mmkg skg A m V s kg sm sN g w m 6.41 )025.0)(4/)(/998( /4.20 81.1 )12.0)(4/)(/998( /4.20 ;4.20 /81.9 /200 23 2 2 23 1 1 2 === ====== ? ? ? ? .8129048)81.16.41)(4.20()12.0( 4 )800000( :or,)( 2 121,1 Ans s m s kg mPaF VVmApFF gagex N8240=?=??= ?=+?=? ? CV Solution: Let the CV enclose all three jets and the surface of the plate. Analyze the force and momentum balance tangential to the plate: tt 2 3 1 FF0mVm(V)mVcos mV (1 )m V m V cos 0, solve for .Ans ? ?? ? ? ?=== + ?? =?? ? = = 1 (1 cos ) 2 + ? The jet mass flow cancels out. Jet (3) has a fractional flow (1 ? ?) = (1/2)(1 ? cos?). 3.47 A liquid jet Vj of diameter Dj strikes a fixed cone and deflects back as a conical sheet at the same velocity. Find the cone angle ? for which the restraining force F = (3/2)?AjVj 2 . Fig. P3.47 Solution: Let the CV enclose the cone, the jet, and the sheet. Then, x out out in in j j j j FFmumum(Vcos)mV,whermAV? ??=?= ? =? ? = 22 jj jj 31 Solve for F A V (1 cos ) A V if cos or . 22 Ans??? ??=+= = =60° 3.48 The small boat is driven at steady speed Vo by compressed air issuing from a 3-cm-diameter hole at Ve = 343 m/s and pe = 1 atm, Te = 30°C. Neglect air drag. The hull drag is kVo 2 , where k = 19 N ? s 2 /m 2 . Estimate the boat speed Vo. Fig. P3.48 Solutions Manual ? Fluid Mechanics, Fifth Edition 208 Solution: For a CV enclosing the boat and moving to the right at boat speed Vo, the air appears to leave the left side at speed (Vo + Ve). The air density is pe/RTe ? 1.165 kg/m 3 . The only mass flow across the CS is the air moving to the left. The force balance is 2 x o out out e e o e o e F Drag kV m u [ A (V V )]( V V ),??=? =? = = + ?? 22 2 2 2 ee o e o o o or: A (V V ) kV , (1.165)( /4)(0.03) (V 343) 19V??+= + = oo work out the numbers: (V 343) V (23060), solve for .Ans+=? o V2.27 m/s= 3.49 The horizontal nozzle in Fig. P3.49 has D1 = 12 in, D2 = 6 in, with p1 = 38 psia and V2 = 56 ft/s. For water at 20°C, find the force provided by the flange bolts to hold the nozzle fixed. Solution: For an open jet, p2 = pa = 15 psia. Subtract pa everywhere so the only nonzero pressure is p1 = 38 ? 15 = 23 psig. Fig. P3.49 Chapter 3 ? Integral Relations for a Control Volume 209 The mass balance yields the inlet velocity: 22 11 ft V (12) (56) (6) , V 14 44 s ? ? == The density of water is 1.94 slugs per cubic foot. Then the horizontal force balance is 2 x bolts 2 2 1 1 2 1 F F (23 psig) (12 in) m u m u m(V V ) 4 ? ?=? + = ? = ? 2 bolts ft ft Compute F 2601 (1.94) (1 ft) 14 56 14 . 4ss Ans ? ??? ? =? ? ? ??? ? ??? ? 1700 lbf 3.50 The jet engine in Fig. P3.50 admits air at 20°C and 1 atm at (1), where A1 = 0.5 m 2 and V1 = 250 m/s. The fuel-air ratio is 1:30. The air leaves section (2) at 1 atm, V2 = 900 m/s, and A2 = 0.4 m 2 . Compute the test stand support reaction Rx needed. Solution: ?1 = p/RT = 101350/[287(293)] = 1.205 kg/m 3 . For a CV enclosing the engine, Fig. P3.50 1111 2 1 m A V (1.205)(0.5)(250) 151 kg/s, m 151 1 156 kg/s 30 ? ?? == = =+= ?? ?? x x 2 2 1 1 fuel fuel F R m u m u m u 156(900) 151(250) 0 .Ans?= = ? ? = ? ?? 102,000 N 3.51 A liquid jet of velocity Vj and area Aj strikes a single 180° bucket on a turbine wheel rotating at angular velocity ?. Find an expression for the power P delivered. At what ? is the power a maximum? How does the analysis differ if there are many buckets, so the jet continually strikes at least one? Fig. P3.51 Solutions Manual ? Fluid Mechanics, Fifth Edition 210 Chapter 3 ? Integral Relations for a Control Volume 211 Solution: Let the CV enclose the bucket and jet and let it move to the right at bucket velocity V = ?R, so that the jet enters the CV at relative speed (Vj ? ?R). Then, x bucket out in jj F F mu mu m[ (V R)] m[V R] ?=? = ? =???? ?? 2 bucket j j j or: F 2m(V R) 2 A (V R) ,?=??= ?? bucket and the power is RF .Ans=? = 2 jj P2R(VR)? ??? Maximum power is found by differentiating this expression: 3 max j j dP 8 0 if . whence P A V d27 Ans ? ?? == ?? ? ?? j V R 3 ?= If there were many buckets, then the full jet mass flow would be available for work: available j j j j j mAV,P2AVR(VR), Ans.??==??? j3 max j j V 1 PAVatR 22 =?=? 3.52 The vertical gate in a water channel is partially open, as in Fig. P3.52. Assuming no change in water level and a hydrostatic pressure distribution, derive an expression for the streamwise force Fx on one-half of the gate as a function of (?, h, w, ?, V1). Apply your result to the case of water at 20°C, V1 = 0.8 m/s, h = 2 m, w = 1.5 m, and ? = 50°. Solution: Let the CV enclose sections (1) and (2), the centerline, and the inside of the gate, as shown. The volume flows are 12 211 W1 VWh VBh, or: V V V B1sin? === ? Solutions Manual ? Fluid Mechanics, Fifth Edition 212 since B = W ? W sin?. The problem is unrealistically idealized by letting the water depth remain constant, whereas actually the depth would decrease at section 2. Thus we have no net hydrostatic pressure force on the CV in this model! The force balance reduces to xgate on fluid 2 1 1 2 1 F F mV mV , where m WhV and V V /(1 sin )? ??= = ? = = ? fluid on gate Solve for F . ) Ans ?? = ?? ?? ?? ? ? ? 2 1 1 WhV 1 ( ) (1 sin to the left This is unrealistic?the pressure force would turn this gate force around to the right. For the particular data given, W = 1.5 m, ? = 50°, B = W(1 ? sin? ) = 0.351 m, V1 = 0.8 m/s, thus V2 = V1/(1 ? sin 50°) = 3.42 m/s, ? = 998 kg/m 3 , h = 2 m. Thus compute 2 fluid on gate 1 F (998)(2)(1.5)(0.8) 1 . 1sin50 Ans ?? =??? ?? ?° ?? 6300 N 3.53 Consider incompressible flow in the entrance of a circular tube, as in Fig. P3.53. The inlet flow is uniform, u1 = Uo. The flow at section 2 is developed pipe flow. Find the wall drag force F as a function of (p1, p2, ?, Uo, R) if the flow at section 2 is 2 2max 2 (a) Laminar: 1 r uu R ?? =? ?? ?? 1/7 2max (b) Turbulent: 1 r uu R ?? ?? ?? ?? Fig. P3.53 Solution: The CV encloses the inlet and outlet and is just inside the walls of the tube. We don?t need to establish a relation between umax and Uo by integration, because the results for these two profiles are given in the text. Note that Uo = uav at section (2). Now use these results as needed for the balance of forces: R 222 x12 drag 22 o o o2 0 F(pp)RF u(u rdr)U(RU) RU( 1)?????????=? ? = ? = ? ? Chapter 3 ? Integral Relations for a Control Volume 213 We simply insert the appropriate momentum-flux factors ? from p. 136 of the text: (a) Laminar: . (a)Ans 222 drag 1 2 o F(pp)R(1/3)RU=? ???? (b) ? ? 2 Turbulent, 1.020: . (b)Ans 222 drag 1 2 o F (p p ) R 0.02 R U=? ???? 3.54 For the pipe-flow reducing section of Fig. P3.54, D1 = 8 cm, D2 = 5 cm, and p2 = 1 atm. All fluids are at 20°C. If V1 = 5 m/s and the manometer reading is h = 58 cm, estimate the total horizontal force resisted by the flange bolts. Fig. P3.54 Solution: Let the CV cut through the bolts and through section 2. For the given manometer reading, we may compute the upstream pressure: 12 mercwater p p ( )h (132800 9790)(0.58 m) 71300 Pa (gage)? ??= ? = ? ? Now apply conservation of mass to determine the exit velocity: 22 12 2 2 Q Q , or (5 m/s)( /4)(0.08 m) V ( /4)(0.05) , solve for V 12.8 m/s??==? Finally, write the balance of horizontal forces: x bolts 1,gage 1 2 1 FF pAm(VV),?=? + = ? 22 bolts or: F (71300) (0.08) (998) (0.08) (5.0)[12.8 5.0] . 44 Ans ? ? =? ?163 N 3.55 In Fig. P3.55 the jet strikes a vane which moves to the right at constant velocity Vc on a frictionless cart. Compute (a) the force Fx required to restrain the cart and (b) the power P delivered to the cart. Also find the cart velocity for which (c) the force Fx is a maximum and (d) the power P is a maximum. Fig. P3.55 Solution: Let the CV surround the vane and cart and move to the right at cart speed. The jet strikes the vane at relative speed Vj ? Vc. The cart does not accelerate, so the horizontal force balance is 2 xx jjcjc jjc F F [A(VV)](VV)cos A(VV)????=?= ? ? ? ? x or: F . (a)Ans= 2 jj c A(V V)(1 cos )?? Solutions Manual ? Fluid Mechanics, Fifth Edition 214 cx The power delivered is P V F . (b)Ans==?? 2 jc j c A V (V V ) (1 cos )?? = c The maximum force occurs when the cart is fixed, or: V . (c)Ans0 The maximum power = = cc occurs when dP/dV 0, or: V / . (d)Ans j V3 3.56 Water at 20°C flows steadily through the box in Fig. P3.56, entering station (1) at 2 m/s. Calculate the (a) horizontal; and (b) vertical forces required to hold the box stationary against the flow momentum. Solution: (a) Summing horizontal forces, x x out out in in FRmu mu?== ? Fig. P3.56 22 (998) (0.03 )(5.56) ( 5.56) (998) (0.05 )(2) ( 2)(cos65 ) 44 x R Ans. ?????? ?? ?? =???° ?? ?? ???? ?? ?? ???? =?18.46 N = Rx to the left18.5 N ??? ?==? =? ? °= ?? ?? 2 (998) (0.05 )(2)( 2 sin65 ) 4 y y in in FR mu up7.1 N 3.57 Water flows through the duct in Fig. P3.57, which is 50 cm wide and 1 m deep into the paper. Gate BC completely closes the duct when ? = 90°. Assuming one- dimensional flow, for what angle ? will the force of the exit jet on the plate be 3 kN? Solution: The steady flow equation applied to the duct, Q1 = Q2, gives the jet velocity as V2 = V1(1 ? sin?). Then for a force summation for a control volume around the jet?s impingement area, Fig. P3.57 ?? ? ?? ?== = ? ?? ? ?? 2 2 11 1 1 (sin)() () 1sin xjj FFmV hh D V ? ? ?? ???? =? =? = ???? ???? 2 2 1111 (998)(0.5)(1)(1.2) sin 1 sin 1 3000 hDV Ans. F 49.5° Chapter 3 ? Integral Relations for a Control Volume 215 3.58 The water tank in Fig. P3.58 stands on a frictionless cart and feeds a jet of diameter 4 cm and velocity 8 m/s, which is deflected 60° by a vane. Compute the tension in the supporting cable. Solution: The CV should surround the tank and wheels and cut through the cable and the exit water jet. Then the horizontal force balance is Fig. P3.58 22 x cable out out j j F T m u ( AV )V cos 998 (0.04) (8) cos60 . 4 Ans ? ?? ?? ?= = = = °= ?? ?? 40 N 3.59 A pipe flow expands from (1) to (2), causing eddies as shown. Using the given CV and assuming p = p1 on the corner annular ring, show that the downstream pressure is given by, neglecting wall friction, 2 11 21 1 22 AA pp V 1 AA ? ??? ? =+ ? ??? ? ??? ? Fig. P3.59 Solution: From mass conservation, V1A1 = V2A2. The balance of x-forces gives x11wal2 1 22 21 11 2 112 FpAp(AA)pAm(VV),wherem AV,VVA/A??= + ? ? = ? = = wall 1 If p p as given, this reduces to .Ans ?? = ?? ?? 211 21 1 22 AA pp V1=+ ?? 3.60 Water at 20°C flows through the elbow in Fig. P3.60 and exits to the atmo- sphere. The pipe diameter is D1 = 10 cm, while D2 = 3 cm. At a weight flow rate of 150 N/s, the pressure p1 = 2.3 atm (gage). Neglect-ing the weight of water and elbow, estimate the force on the flange bolts at section 1. Fig. P3.60 216 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: First, from the weight flow, compute Q = (150 N/s)/(9790 N/m 3 ) = 0.0153 m 3 /s. Then the velocities at (1) and (2) follow from the known areas: 12 22 Q 0.0153 m Q 0.0153 m V 1.95 ; V 21.7 AsA s( /4)(0.1) ( /4)(0.03)?? == = == = The mass flow is ?A1V1 = (998)(?/4)(0.1) 2 (1.95) ? 15.25 kg/s. Then the balance of forces in the x-direction is: xbolts11 21 2 1 2 bolts F F p A mu mu m( V cos40 V ) solve for F (2.3 101350) (0.1) 15.25(21.7cos 40 1.95) . 4 Ans ? ?=? + = ? =? °? =× + °+ ? 2100 N 3.61 A 20°C water jet strikes a vane on a tank with frictionless wheels, as shown. The jet turns and falls into the tank without spilling. If ? = 30°, estimate the horizontal force F needed to hold the tank stationary. Solution: The CV surrounds the tank and wheels and cuts through the jet, as shown. We have to assume that the splashing into the tank does not increase the x-momentum of the water in the tank. Then we can write the CV horizontal force relation: Fig. P3.61 () ? ???=?= ? =? ? xinijet tank d F F u d m u 0 mV independent of dt 22 2 jj 3 slug 2 ft Thus F A V 1.94 ft 50 . 412 sft Ans ? ? ?????? == ? ?????? ?????? 106 lbf 3.62 Water at 20°C exits to the standard sea-level atmosphere through the split nozzle in Fig. P3.62. Duct areas are A1 = 0.02 m 2 and A2 = A3 = 0.008 m 2 . If p1 = 135 kPa (absolute) and the flow rate is Q2 = Q3 = 275 m 3 /h, compute the force on the flange bolts at section 1. Fig. P3.62 Chapter 3 ? Integral Relations for a Control Volume 217 Solution: With the known flow rates, we can compute the various velocities: 3 23 1 2 275/3600 m /s m 550/3600 m V V 9.55 ; V 7.64 s0.02s0.008 m == = = = The CV encloses the split nozzle and cuts through the flange. The balance of forces is x bolts 1,gage 1 2 2 3 3 1 1 F F p A Q( Vcos30) Q( Vcos30) Q( V),? ???=? + = ? °+ ? °? + bolts 275 550 or: F 2(998) (9.55cos30 ) 998 (7.64) (135000 101350)(0.02) 3600 3600 ?? ?? =°++ ?? ?? ?? ?? 1261 1165 673 .Ans=++?3100 N P3.63 In Example 3.10, the gate force F is a function of both water depth and velocity. (a) Non-dimensionalize the force by dividing by (?gbh 1 2 ) and plot this force versus h 2 /h 1 ? 1.0. (b) The plot involves a second dimensionless parameter involving V 1 . Do you know its name? (c) For what condition h 2 /h 1 is the force largest? (d) For small values of V 1 , the force becomes negative (to the right), which is totally unrealistic. Can you explain why? Solution: The original solution for gate force in Ex. 3.10 was (a) When we divide through by (?gbh 1 2 ), we obtain the dimensionless force relation (b) On the right hand side is a new dimensionless group, [V 1 2 /(gh 1 )], which is called the Froude number at section 1. Ans.(b) As an extra requirement of part (a), we can plot the dimensionless force versus h 2 /h 1 ? 1.0 for various values of the Froude number [V 1 2 /(gh 1 )], as follows: )1(])(1[ 2 2 12 11 2 1 22 1 ???= h h bVh h h gbhF gate ? ? ).()1()(])(1[ 2 1 2 1 1 2 12 1 2 2 1 aAns h h gh V h h gbh F ???= ? 218 Solutions Manual ? Fluid Mechanics, Fifth Edition 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0 0.2 0.4 0.6 0.8 1 h 2 /h 1 0.05 0.10 0.15 0.20 Froude Number: F /(?gbh 1 2 ) (c) For everything held constant except h 2 , the maximum force is found by differentiation: (d) We see that, at small h 2 /h 1 , the force becomes negative and is not plotted. Presently the writer does not know exactly why this happens, but when it does, Fr 2 is very large, > 8. 3.64 The 6-cm-diameter 20°C water jet in Fig. P3.64 strikes a plate containing a hole of 4-cm diameter. Part of the jet passes through the hole, and part is deflected. Determine the horizontal force required to hold the plate. Solution: First determine the incoming flow and the flow through the hole: Fig. P3.64 32 22 in hole mm Q (0.06) (25) 0.0707 , Q (0.04) (25) 0.0314 4s4s ?? == == ).(or)/(yieldswhich0 3/1 1 2 1 1 23/12 1 2 12 2 )( cAns gh V h h ghVh dh dF === Chapter 3 ? Integral Relations for a Control Volume 219 Then, for a CV enclosing the plate and the two jets, the horizontal force balance is x plate hole hole upper upper lower lower in in FF mu m mu mu (998)(0.0314)(25) 0 0 (998)(0.0707)(25) 784 1764, solve for .Ans ?=? = + + ? =+? =? F 980 N (to left)? 3.65 The box in Fig. P3.65 has three 0.5-in holes on the right side. The volume flows of 20°C water shown are steady, but the details of the interior are not known. Compute the force, if any, which this water flow causes on the box. Solution: First we need to compute the velocities through the various holes: Fig. P3.65 3 top bottom middle top 2 0.1 ft /s V V 73.3 ft/s; V 2V 146.6 ft/s ( /4)(0.5/12)? == = == Pretty fast, but do-able, I guess. Then make a force balance for a CV enclosing the box: x box in in top top in middle top top FF mu 2mu,whereu V andu V?= =? + =? = box Solve for F (1.94)(0.2)(146.6) 2(1.94)(0.1)(73.3) .Ans=+?85 lbf 3.66 The tank in Fig. P3.66 weighs 500 N empty and contains 600 L of water at 20°C. Pipes 1 and 2 have D = 6 cm and Q = 300 m 3 /hr. What should the scale reading W be, in newtons? Solution: Let the CV surround the tank, cut through the two jets, and slip just under the tank bottom, as shown. The relevant jet velocities are Fig. P3.66 3 12 2 Q (300/3600) m /s V V 29.5 m/s A (/4)(0.06 m)? === ? The scale reads force ?P? on the tank bottom. Then the vertical force balance is z tank water 2 2 1 1 1 FPW W mvmvm[0(V)]? =? ? = ? = ?? 220 Solutions Manual ? Fluid Mechanics, Fifth Edition 3 300 Solve for 500 9790(0.6 m ) 998 (29.5) . 3600 Ans ?? =+ + ? ?? ?? P 8800 N 3.67 Gravel is dumped from a hopper, at a rate of 650 N/s, onto a moving belt, as in Fig. P3.67. The gravel then passes off the end of the belt. The drive wheels are 80 cm in diameter and rotate clockwise at 150 r/min. Neglecting system friction and air drag, estimate the power required to drive this belt. Fig. P3.67 Solution: The CV goes under the gravel on the belt and cuts through the inlet and outlet gravel streams, as shown. The no-slip belt velocity must be belt outlet wheel rev rad 1 min m V V R 150 2 (0.4 m) 6.28 min rev 60 s s ? ?? ==?= ? ?? ?? Chapter 3 ? Integral Relations for a Control Volume 221 Then the belt applies tangential force F to the gravel, and the force balance is x on belt out out in in in F F m u m u , but u 0.?= = ? = belt out 650 kg m Then F mV 6.28 416 N 9.81 s s ???? == = ???? ???? belt The power required to drive the belt is FV (416)(6.28) .Ans= =?P 2600 W 3.68 The rocket in Fig. P3.68 has a super- sonic exhaust, and the exit pressure pe is not necessarily equal to pa. Show that the force F required to hold this rocket on the test stand is F = ?eAeVe 2 + Ae(pe ? pa). Is this force F what we term the thrust of the rocket? Fig. P3.68 Solution: The appropriate CV surrounds the entire rocket and cuts through the exit jet. Subtract pa everywhere so only exit pressure ? 0. The horizontal force balance is xeaeefo fo eee F F (p p )A m u m u m u , but u u 0, m A V??=?? = ? ? == = Thus .Ans 2 eee e a e F= A V (p p )A (the )? +? thrust 3.69 A uniform rectangular plate, 40 cm long and 30 cm deep into the paper, hangs in air from a hinge at its top, 30-cm side. It is struck in its center by a horizontal 3-cm- diameter jet of water moving at 8 m/s. If the gate has a mass of 16 kg, estimate the angle at which the plate will hang from the vertical. Solution: The plate orientation can be found through force and moment balances, Fig. P3.69 22 (998) (0.03 )(8 ) 45.1 4 x j in in FF mu N ? ?? ?==? =? = ?? ?? ? ??==? +0 (45)(0.02)(sin ) (16)(9.81)(0.02)(cos ) B M 16? =° 222 Solutions Manual ? Fluid Mechanics, Fifth Edition Chapter 3 ? Integral Relations for a Control Volume 223 3.70 The dredger in Fig. P3.70 is loading sand (SG = 2.6) onto a barge. The sand leaves the dredger pipe at 4 ft/s with a weight flux of 850 lbf/s. Estimate the tension on the mooring line caused by this loading process. Solution: The CV encloses the boat and cuts through the cable and the sand flow jet. Then, Fig. P3.70 x cable sand sand sand FT mu mVcos,??=? =? =? cable 850 slug ft or: T 4 cos30 . 32.2 s s Ans ???? =°? ???? ???? 91 lbf 3.71 Suppose that a deflector is deployed at the exit of the jet engine of Prob. 3.50, as shown in Fig. P3.71. What will the reaction Rx on the test stand be now? Is this reaction sufficient to serve as a braking force during airplane landing? Solution: From Prob. 3.50, recall that the essential data was Fig. P3.71 12 1 2 V 250 m/s, V 900 m/s, m 151 kg/s, m 156 kg/s= === The CV should enclose the entire engine and also the deflector, cutting through the support and the 45° exit jets. Assume (unrealistically) that the exit velocity is still 900 m/s. Then, x x out out in in out out in 1 F R m u m u , where u V cos 45 and u V?= = ? =? ° = x Then R 156(900 cos 45 ) 151(250) 137,000 N=? °? =? .AnsThe support reaction is to the left and equals 137 kN 3.72 A thick elliptical cylinder immersed in a water stream creates the idealized wake shown. Upstream and downstream pressures are equal, and Uo = 4 m/s, L = 80 cm. Find the drag force on the cylinder per unit width into the paper. Also compute the dimensionless drag coefficient CD = 2F/(? Uo 2 bL). Fig. P3.72 224 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: This is a ?numerical? version of the ?analytical? body-drag Prob. 3.44. The student still must make a CV analysis similar to Prob. P3.44 of this Manual. The wake is exactly the same shape, so the result from Prob. 3.44 holds here also: 22 drag o 11 F U Lb (998)(4) (0.8)(1.0) . 33 Ans?== ?4260 N The drag coefficient is easily calculated from the above result: CD = 2/3. Ans. 3.73 A pump in a tank of water directs a jet at 45 ft/s and 200 gal/min against a vane, as shown in the figure. Compute the force F to hold the cart stationary if the jet follows (a) path A; or (b) path B. The tank holds 550 gallons of water at this instant. Solution: The CV encloses the tank and passes through jet B. (a) For jet path A, no momentum flux crosses the CV, therefore F = 0 Ans. (a) Fig. P3.73 (b) For jet path B, there is momentum flux, so the x-momentum relation yields: x out out jet B FFmu mu?== = Now we don?t really know uB exactly, but we make the reasonable assumption that the jet trajectory is frictionless and maintains its horizontal velocity component, that is, uB ? Vjet cos 60°. Thus we can estimate ???? == °? ???? ???? 3 3 200 1.94 (45cos60 ) . (b) 448.8 B slug ft Fmu Ans sft 19.5 lbf 3.74 Water at 20°C flows down a vertical 6-cm-diameter tube at 300 gal/min, as in the figure. The flow then turns horizontally and exits through a 90° radial duct segment 1 cm thick, as shown. If the radial outflow is uniform and steady, estimate the forces (Fx, Fy, Fz) required to support this system against fluid momentum changes. Chapter 3 ? Integral Relations for a Control Volume 225 Solution: First convert 300 gal/min = 0.01893 m 3 /s, hence the mass flow is ?Q = 18.9 kg/s. The vertical-tube velocity (down) is Vtube = 0.01893/[(?/4)(0.06) 2 ] = ?6.69 k m/s. The exit tube area is (?/2)R?h = (?/2)(0.15)(0.01) = 0.002356 m 2 , hence Vexit = Q/Aexit = 0.01893/0.002356 = 8.03 m/s. Now estimate the force components: ?? ? +° ?° ?== = ? ? ? ?? 45 45 sin . (a) xoutoutexit FudmV hRdAns x F0 ?? ? ? +° ?° ?== ? = ? ? ?=? ? ?? 45 45 cos 0 2 y out out in exit exit FvdmmvV hRdVhR y F =? ?(8.03)(998)(0.01)(0.15) 2 . (b)or: Ans y F17N? ?== ? = ?? ? ( ) (18.9 /)[0 ( 6.69 /)] . (c) zoutin Fmww kgs ms Ans z F 126 N+ 3.75 A liquid jet of density r and area A strikes a block and splits into two jets, as shown in the figure. All three jets have the same velocity V. The upper jet exits at angle ? and area ?A, the lower jet turns down at 90° and area (1 ? ?)A. (a) Derive a formula for the forces (Fx,Fy) required to support the block against momentum changes. (b) Show that Fy = 0 only if ? ? 0.5. (c) Find the values of ? and ? for which both Fx and Fy are zero. Solution: (a) Set up the x- and y-momentum relations: ? ?? ??? ?== ? ?? = ?== +? ? (cos) () sin (1 ) ( ) xx yy F F mV mV wherem AVoftheinletjet FF mV mV Clean this up for the final result: . (a) x y F FAns = =? mV(1 cos ) mV( sin 1) ? + ?? ??? (b) Examining Fy above, we see that it can be zero only when, ? ? ? ? = 1 sin But this makes no sense if ? < 0.5, hence Fy = 0 only if ? ? 0.5. Ans. (b) 226 Solutions Manual ? Fluid Mechanics, Fifth Edition (c) Examining Fx, we see that it can be zero only if cos? = 1/?, which makes no sense unless ? = 1, ? = 0°. This situation also makes Fx = 0 above (sin? = 0). Therefore the only scenario for which both forces are zero is the trivial case for which all the flow goes horizontally across a flat block: xy F F 0 only if: , . (c)Ans? ?= ===10° 3.76 A two-dimensional sheet of water, 10 cm thick and moving at 7 m/s, strikes a fixed wall inclined at 20° with respect to the jet direction. Assuming frictionless flow, find (a) the normal force on the wall per meter of depth, and the widths of the sheet deflected (b) upstream, and (c) downstream along the wall. Fig. P3.76 Solution: (a) The force normal to the wall is due to the jet?s momentum, 2 (998)(0.1)(7 )(cos70 ) Ninin F mu Ans.?=? =? °= 1670 /Nm (b) Assuming V1 = V2 = V3 = Vjet, VjA1 = VjA2 + VjA3 where, ?== =? 21 A A sin (0.1)(1)(sin 20°) 0.034 m Ans.3cm (c) Similarly, A3 = A1 cos? = (0.1)(1)(cos 20°) = 0.094 m ? 9.4 cm Ans. 3.77 Water at 20°C flows steadily through a reducing pipe bend, as in Fig. P3.77. Known conditions are p1 = 350 kPa, D1 = 25 cm, V1 = 2.2 m/s, p2 = 120 kPa, and D2 = 8 cm. Neglecting bend and water weight, estimate the total force which must be resisted by the flange bolts. Solution: First establish the mass flow and exit velocity: Fig. P3.77 22 111 2 2 kg m m A V 998 (0.25) (2.2) 108 998 (0.08) V , or V 21.5 4s4 s ?? ? ?? ?? == == = ?? ?? ?? ?? Chapter 3 ? Integral Relations for a Control Volume 227 The CV surrounds the bend and cuts through the flanges. The force balance is x bolts 1,gage 1 2,gage 2 2 2 1 1 2 2 1 1 FF pApAmumu,wheruVanduV?=? + + = ? =? = 22 bolts or F (350000 100000) (0.25) (120000 100000) (0.08) 108(21.5 2.2) 44 12271 101 2553 . ?? =? +? ++ =++?14900 N Ans 3.78 A fluid jet of diameter D1 enters a cascade of moving blades at absolute velocity V1 and angle ?1, and it leaves at absolute velocity V1 and angle ?2, as in Fig. P3.78. The blades move at velocity u. Derive a formula for the power P delivered to the blades as a function of these parameters. Solution: Let the CV enclose the blades and move upward at speed u, so that the flow appears steady in that frame, as shown at right. The relative velocity Vo may be eliminated by the law of cosines: 222 o1 1 1 22 2 VVu2Vucos V u 2V ucos ? ? =+? =+? Fig. P3.78 () 22 12 112 2 (1/2) V V solve for u V cos V cos? ? ? = ? Then apply momentum in the direction of blade motion: y vanes jet o1y o2y 1 1 2 2 1 1 F F m (V V ) m(V cos V cos ), m A V? ???= = ? = ? = The power delivered is P = Fu, which causes the parenthesis ?cos ? ? terms to cancel: () Ans. 22 jet 1 2 1 PFu m V V 2 == ? 228 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.79 Air at 20°C and 1 atm enters the bottom of an 85° conical flowmeter duct at a mass flow rate of 0.3 kg/s, as shown in the figure. It supports a centered conical body by steady annular flow around the cone and exits at the same velocity as it enters. Estimate the weight of the body in newtons. Solution: First estimate the velocity from the known inlet duct size: 3 2 101350 kg 1.205 , 287(293) m m 0.3 (1.205) (0.1) , 4s air p RT thus m AV V solve ? ? ? == = == = V 31.7= Then set up the vertical momentum equation, the unknown is the body weight: ?=?= °? = °? cos 42.5 (cos 42.5 1) z F W mV mV mV =?°=(0.3)(31.7)(1 cos 42.5 )Thus Ans. cone W2.5 N 3.80 A river (1) passes over a ?drowned? weir as shown, leaving at a new condition (2). Neglect atmospheric pressure and assume hydrostatic pressure at (1) and (2). Derive an expression for the force F exerted by the river on the obstacle. Neglect bottom friction. Fig. P3.80 Solution: The CV encloses (1) and (2) and cuts through the gate along the bottom, as shown. The volume flow and horizontal force relations give 11 2 2 Vbh Vbh= xweir 11 22 1121 11 F F gh (h b) gh (h b) ( h bV )(V V ) 22 ????=? + ? = ? Note that, except for the different geometry, the analysis is exactly the same as for the sluice gate in Ex. 3.10. The force result is the same, also: () .Ans ?? ?? ?? 22 21 weir 1 2 1 1 2 1h FgbhhhbV 2h =?? ? ?? Chapter 3 ? Integral Relations for a Control Volume 229 3.81 Torricelli?s idealization of efflux from a hole in the side of a tank is 2,Vgh? as shown in Fig. P3.81. The tank weighs 150 N when empty and contains water at 20°C. The tank bottom is on very smooth ice (static friction coefficient ? ? 0.01). For what water depth h will the tank just begin to move to the right? Fig. P3.81 Solution: The hole diameter is 9 cm. The CV encloses the tank as shown. The coefficient of static friction is ? = 0.01. The x-momentum equation becomes 2 x tank out hole F W mu m V AV A(2gh) ???? =? = =? =? =? 22 or: 0.01 (9790) (1 m) (h 0.3 0.09) 150 998 (0.09) (2)(9.81)h 44 ?? ???? ++ + = ?? ?? ???? Solve for .Ansh0.6m? 3.82 The model car in Fig. P3.82 weighs 17 N and is to be accelerated from rest by a 1-cm-diameter water jet moving at 75 m/s. Neglecting air drag and wheel friction, estimate the velocity of the car after it has moved forward 1 m. Fig. P3.82 Solution: The CV encloses the car, moves to the left at accelerating car speed V(t), and cuts through the inlet and outlet jets, which leave the CS at relative velocity Vj ? V. The force relation is Eq. (3.50): dm x rel car car out out in in jet j Fa 0mamumu 2m(VV),?? =? = ? =? ? ? dV dt 2 car j j or: m 2 A (V V)?=? Except for the factor of ?2,? this is identical to the ?cart? analysis of Example 3.12 on page 140 of the text. The solution, for V = 0 at t = 0, is given there: 2 2 jj 1 j car VKt 2 A 2(998)( /4)(0.01) V , where K 0.0905 m 1VKt m (17/9.81) ? ? ? == = + 230 Solutions Manual ? Fluid Mechanics, Fifth Edition dt t 0 509t Thus V (in m/s) and then compute distance S V 1 6.785t == + ? The initial acceleration is 509 m/s 2 , quite large. Assuming the jet can follow the car without dipping, the car reaches S = 1 m at t ? 0.072 s, where V ? 24.6 m/s. Ans. 3.83 Gasoline at 20°C is flowing at V1 = 12 m/s in a 5-cm-diameter pipe when it encounters a 1-m length of uniform radial wall suction. After the suction, the velocity has dropped to 10 m/s. If p1 = 120 kPa, estimate p2 if wall friction is neglected. Solution: The CV cuts through sections 1 and 2 and the inside of the walls. We compute the mass flow at each section, taking ? ? 680 kg/m 3 for gasoline: 22 12 kg kg m 680 (0.05) (12) 16.02 ; m 680 (0.05) (10) 13.35 4s4s ?? ?? ?? ==== ?? ?? ?? ?? The difference, 16.02 ? 13.35 = 2.67 kg/s, is sucked through the walls. If wall friction is neglected, the force balance (taking the momentum correction factors ? ? 1.0) is: 2 x1122 22 11 2 2 F p A p A m V m V (120000 p ) (0.05) 4 (13.35)(10) (16.02)(12), solve for p .Ans ? ?= ? = ? = ? =? ? 150 kPa 3.84 Air at 20°C and 1 atm flows in a 25-cm-diameter duct at 15 m/s, as in Fig. P3.84. The exit is choked by a 90° cone, as shown. Estimate the force of the airflow on the cone. Solution: The CV encloses the cone, as shown. We need to know exit velocity. The exit area is approximated as a ring of diameter 40.7 cm and thickness 1 cm: Fig. P3.84 3 2 11 2 2 2 2 mm Q A V (0.25) (15) 0.736 A V (0.407)(0.01)V , or V 57.6 4s s ? ?== = =? ? Chapter 3 ? Integral Relations for a Control Volume 231 The air density is ? = p/RT = (101350)/[287(293)] ? 1.205 kg/m 3 . We are not given any pressures on the cone so we consider momentum only. The force balance is xcone outin F F m(u u ) (1.205)(0.736)(57.6cos 45° 15) Ans.?= = ? = ? ? 22.8 N The force on the cone is to the right because we neglected pressure forces. 3.85 The thin-plate orifice in Fig. P3.85 causes a large pressure drop. For 20°C water flow at 500 gal/min, with pipe D = 10 cm and orifice d = 6 cm, p1 ? p2 ? 145 kPa. If the wall friction is negligible, estimate the force of the water on the orifice plate. Fig. P3.85 Solution: The CV is inside the pipe walls, cutting through the orifice plate, as shown. At least to one-dimensional approximation, V1 = V2, so there is no momentum change. The force balance yields the force of the plate on the fluid: x plate on fluid 1 1 2 2 wall wall 2 1 FF pApA A m(VV)0??=? + ? ? = ? ? 2 wall plate Since 0, we obtain F (145000) (0.1) 4 Ans. ? ? ?=?1140 N The force of the fluid on the plate is opposite to the sketch, or to the right. 3.86 For the water-jet pump of Prob. 3.36, add the following data: p1 = p2 = 25 lbf/in 2 , and the distance between sections 1 and 3 is 80 in. If the average wall shear stress between sections 1 and 3 is 7 lbf/ft 2 , esti- mate the pressure p3. Why is it higher than p1? Fig. P3.36 Solution: The CV cuts through sections 1, 2, 3 and along the inside pipe walls. Recall from Prob. 3.36 that mass conservation led to the calculation V3 ? 6.33 m/s. Convert data to SI units: L = 80 in = 2.032 m, p1 = p2 = 25 psi = 172.4 kPa, and ?wall = 7 psf = 335 Pa. We need mass flows for each of the three sections: 2 1 22 2 3 kg m 998 (0.0762) (40) 82 ; 4s kg kg m 998 [(0.254) (0.0762) ](3) 138 and m 182 138 320 4ss ? ? ?? =? 1 ?? ?? ?? = ? ? ?+? ?? ?? 232 Solutions Manual ? Fluid Mechanics, Fifth Edition Then the horizontal force balance will yield the (high) downstream pressure: x11 2 33wal2 33 22 11 2 3 Fp(AA)pA DLmVmVmV (172400 p ) (0.254) 335 ( )(2.032) 320(6.33) 138(3) 182(40) 4 ? ? ? ? ?= + ? ? = ? ? = ? ? 0.254 = ? ? 3 Solve for p Ans.? 274000 Pa The pressure is high because the primary inlet kinetic energy at section (1) is converted by viscous mixing to pressure-type energy at the exit. 3.87 Figure P3.87 simulates a manifold flow, with fluid removed from a porous wall or perforated section of pipe. Assume incompressible flow with negligible wall friction and small suction 1w VV .. If (p1, V1, Vw, ?, D) are known, derive expressions for (a) V2 and (b) p2. Fig. P3.87 Solution: The CV cuts through sections 1 and 2 and runs along the duct wall, as shown. Assuming incompressible flow, mass conservation gives 5D 222 11 2 2 w 2 w 1 0 x VA VA V 1 Ddx V D 2.5 V D V D 5D 4 4 ?? ?? ?? =+ ? = + = ?? ?? ? w1 Assuming V V , solve for (a)Ans.? 21 w V V 10V= Then use this result while applying the momentum relation to the same CV: dm 2 x12 ww2211 ww F(pp)D dA mumu u 4 ? ??=? ? = ? + ?? Since ?w ? 0 and uw ? 0 and the area A1 cancels out, we obtain the simple result ( ) 22 21 1 2 pp VV ( ) (b)Ans.?=+ ? = 1w1w p20VV5V+?? 3.88 The boat in Fig. P3.88 is jet-propelled by a pump which develops a volume flow rate Q and ejects water out the stern at velocity Vj. If the boat drag force is F = kV 2 , where k is a constant, develop a formula for the steady forward speed V of the boat. Fig. P3.88 Chapter 3 ? Integral Relations for a Control Volume 233 Solution: Let the CV move to the left at boat speed V and enclose the boat and the pump?s inlet and exit. Then the momentum relation is 2 x pump j inlet j inlet j F kV m (V V V ) Q(V V) if we assume V V??= = +? ? + If, further, j VV , then the approximate solution is: V ? (?QVj/k) 1/2 Ans. If V and Vj are comparable, then we solve a quadratic equation: V,wheAns.? 21/2 j Q [2V] 2k ? ?? ? ?++ = 3.89 Consider Fig. P3.36 as a general problem for analysis of a mixing ejector pump. If all conditions (p, ?, V) are known at sections 1 and 2 and if the wall friction is negligible, derive formulas for estimating (a) V3 and (b) p3. Solution: Use the CV in Prob. 3.86 but use symbols throughout. For volume flow, () 2222 2 112 21 3 2 31 2 12 V D V D D V D , or: V V V (1 ), (D /D ) 44 4 ? ?? ???+?= =+?= (A) Now apply x-momentum, assuming (quite reasonably) that p1 = p2: () 22222 13 2w2 23 2 12 11 (p p ) D D L D V D D V D V 4444 ? ?? ? ?? ? ? ???= ??? where ?? ?? ?? ?? ?? w Clean up: .Ans 2 222 1 31 1 2 3 4L D pp V(1 )VV DD =? + +? ? = ? ?? ? ? You have to insert V3 into this answer from Eq. (A) above, but the algebra is messy. 3.90 As shown in Fig. P3.90, a liquid column of height h is confined in a vertical tube of cross-sectional area A by a stopper. At t = 0 the stopper is suddenly removed, exposing the bottom of the liquid to atmospheric pressure. Using a control- volume analysis of mass and vertical momentum, derive the differential equation for the downward motion V(t) of the liquid. Assume one-dimensional, incompressible, frictionless flow. Fig. P3.90 234 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: Let the CV enclose the cylindrical blob of liquid. With density, area, and the blob volume constant, mass conservation requires that V = V(t) only. The CV accelerates downward at blob speed V(t). Vertical (downward) force balance gives ()down rel down out out in in d Fadm VdmVmV0 dt ???? = + ? = ?? ? blob w w blob or: m g p A A am 0?+? ? = ?Since p 0 and 0, we are left with Ans.?== blob dV ag dt == 3.91 Extend Prob. 3.90 to include a linear (laminar) average wall shear stress of the form ? ? cV, where c is a constant. Find V(t), assuming that the wall area remains constant. Solution: The downward momentum relation from Prob. 3.90 above now becomes blob w blob blob dV dV c DL 0m g DLm ,or Vg,where dt dt m ? ?? ? ?=? ? += = where we have inserted the laminar shear ? = cV. The blob mass equals ?(?/4)D 2 L. For V = 0 at t = 0, the solution to this equation is ,where Ans. t blob gcDL4c V (1e ) mD ? =? = = ? ? ? ?? 3.92 A more involved version of Prob. 3.90 is the elbow-shaped tube in Fig. P3.92, with constant cross-sectional area A and diameter ,Dh L. Assume incompressible flow, neglect friction, and derive a differential equation for dV/dt when the stopper is opened. Hint: Combine two control volumes, one for each leg of the tube. Solution: Use two CV?s, one for the vertical blob and one for the horizontal blob, connected as shown by pressure. Fig. P3.92 Chapter 3 ? Integral Relations for a Control Volume 235 From mass conservation, V1 = V2 = V(t). For CV?s #1 and #2, down rel atm I 1 dV F a dm (mv) 0 (p p )A gAh m dt ??? =?==?+ ? ? (No. 1) xrel Iatm 2 dV F a dm (mu) 0 (p p )A 0 m dt ?? =? == ? +? ? (No. 2) Add these two together. The pressure terms cancel, and we insert the two blob masses: dV gAh ( Ah AL) 0, or: . dt Ans????+ = dV h g dt L h = + 3.93 Extend Prob. 3.92 to include a linear (laminar) average wall shear stress of the form ? ? cV, where c is a constant. Find V(t), assuming that the wall area remains constant. Solution: For the same two CV?s as in Prob. 3.92 above, we add wall shears: ? 1 dV pA gAh (cV) Dh m dt ??+? = (No. 1) ? 2 dV pA 0 (cV) DL m dt ??+? = (No. 2) Add together, divide by (?A), A = ?D 2 /4, and rearrange into a 1st order linear ODE: ?? ?? ?? subject to at .Ans o dV 4c gh VV00,h dt D L h += === +? The blob length (L + h) could be assumed constant, but h = h(t). We could substitute for V = ?dh/dt and rewrite this relation as a 2nd order ODE for h(t), but we will not proceed any further with an analytical solution to this differential equation. 3.94 Attempt a numerical solution of Prob. 3.93 for SAE 30 oil at 20°C. Let h = 20 cm, L = 15 cm, and D = 4 mm. Use the laminar shear approximation from Sec. 6.4: ? ? 8?V/D, where ? is the fluid viscosity. Account for the decrease in wall area wetted by the fluid. Solve for the time required to empty (a) the vertical leg and (b) the horizontal leg. Solution: For SAE 30 oil, ? ? 0.29 kg/(m · s) and ? ? 917 kg/m 3 . For laminar flow as given, c = 8?/D, so the coefficient (4c/?D) = 4[8(0.29)/0.004]/[917(0.004)] ? 632 s ?1 . [The flow is highly damped.] Then the basic differential equation becomes t 0 dV 9.81h 632V , with h 0.2 V dt and V(0) 0 dt 0.15 h + ==?= + ? 236 Solutions Manual ? Fluid Mechanics, Fifth Edition We may solve this numerically, e.g., by Runge-Kutta or a spreadsheet or whatever. After h reaches zero, we keep h = 0 and should decrease L = 0.15 ? ? V dt until L = 0. The results are perhaps startling: the highly damped system (lubricating oil in a capillary tube) quickly reaches a ?terminal? (near-zero-acceleration) velocity in 16 ms and then slowly moves down until h ? 0, t ? 70 s. The flow stops, and the horizontal leg will not empty. The computed values of V and h for the author?s solution are as follows: t, s: 0 5 10 15 20 30 40 50 60 70 V, m/s: 0 0.008 0.007 0.006 0.005 0.003 0.001 0.000 0.000 0.000 h, m: 0.2 0.162 0.121 0.089 0.063 0.028 0.011 0.004 0.001 0.000 ________________________________________________________________________ P3.95 A cylindrical water tank discharges through a well-rounded orifice to hit a plate, as in Fig. P3.95. Use the Torricelli formula of Prob. P3.81 to estimate the exit velocity. (a) If, at this instant, the force F required to hold the plate is 40 N, what is the depth h ? (b) If the tank surface is dropping at the rate of 5 cm every 2 seconds, what is the tank diameter D? Solution: For water take ? = 998 kg/m 3 . The control volume surrounds the plate and yields h d = 4 cm F D CV ).( )/81.9)(2()04.0)(4/)(/998( 40 : )2()4/( Thus;2saysTorricelliBut 4 )()( 223 2 2 22 aAns smmmkg N hdataGiven gd F hghV VdVVAVmumFF jet jetjetjetjetjetjetininx m1.63== == ==??=?==? ? ?? ? ?? Fig. P3.95 Chapter 3 ? Integral Relations for a Control Volume 237 (b) In 2 seconds, h drops from 1.63m to 1.58m, not much change. So, instead of a laborious calculus solution, find Q jet,av for an average depth h av = (1.63+1.58)/2 = 1.605 m: ).( )05.0)(4/( )2)(00705.0( )4/( :or,Equate /00705.0)605.1)(/81.9(2)04.0( 4 2 tank 322 bAns m s h tQ DhAtQ smmsmmghAQ avjetav m0.60?= ? ? =?=? ?== ?? ? 238 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.96 Extend Prob. 3.90 to the case of the liquid motion in a frictionless U-tube whose liquid column is displaced a distance Z upward and then released, as in Fig. P3.96. Neglect the short horizontal leg and combine control-volume analyses for the left and right legs to derive a single differential equation for V(t) of the liquid column. Solution: As in Prob. 3.92, break it up into two moving CV?s, one for each leg, as shown. By mass conservation, the velocity V(t) is the same in each leg. Let pI be the bottom pressure in the (very short) cross- over leg. Neglect wall shear stress. Now apply vertical momentum to each leg: Leg#1: down rel Fadm?? ? aI 1 1 dV (p p )A gAh m 0 dt ?=? + ? = Fig. P3.96 up rel I a 2 2 dV Leg#2: F a dm (p p )A gAh m 0 dt ?? ?=???= ? Add these together. The pressure terms will cancel. Substitute for the h?s as follows: 12 1 2 12 dV dV dV gA(h h ) gA(2Z) (m m ) A(h h ) AL dt dt dt ?? ? ??= =+ = + = dZ Since V , we arrive at, finally, dt Ans.=? 2 2 dZ 2g Z0 Ldt += The solution is a simple harmonic oscillation: Z C cos t (2g/L) D sin t (2g/L) . ? ?? ? =+ ? ?? ? 3.97 Extend Prob. 3.96 to include a linear (laminar) average wall shear stress resistance of the form ? ? 8?V/D, where ? is the fluid viscosity. Find the differential equation for dV/dt and then solve for V(t), assuming an initial displacement z = zo, V = 0 at t = 0. The result should be a damped oscillation tending toward z = 0. Solution: The derivation now includes wall shear stress on each leg (see Prob. 3.96): down rel 1 w 1 1 dV Leg#1: F a dm p A gAh Dh m 0 dt ????? =?+ ? ? = ? Chapter 3 ? Integral Relations for a Control Volume 239 up rel 2 w 2 2 dV Leg#2: F a dm p A gAh Dh m 0 dt ????? =??? ? ? = ? Again add these two together: the pressure terms cancel, and we obtain, if A = ?D 2 /4, where Ans. 2 w w 2 4dZ 2g 8 V Z0, DL Ddt ++= = ? ? ? ? The shear term is equal to the linear damping term (32?/?D 2 )(dZ/dt). If we assume an initial static displacement Z = Zo, V = 0, at t = 0, we obtain the damped oscillation ,where and Ans. 2 t/t* o D Z Z e cos( t) t* 2g/L 16 ? === ? ?? ? 3.98 As an extension of Ex. 3.9, let the plate and cart be unrestrained, with fric- tionless wheels. Derive (a) the equation of motion for cart velocity Vc(t); and (b) the time required for the cart to accelerate to 90% of jet velocity. (c) Compute numerical values for (b) using the data from Ex. 3.9 and a cart mass of 2 kg. Solution: (a) Use Eq. (3.49) with arel equal to the cart acceleration and ?Fx = 0: ??? = =? ? , . (a) c xxrel c dV F a m u dA m Ans dt jj j c Vn A V V?=??? 2 () The above 1 st -order differential equation can be solved by separating the variables: 2 00 , () c V t j c cjc A dV Kdt whereK mVV ? == ? ?? 9 :0.90 (b) 1 j c jj j VKt V Solve for if Ans. VVKt KV == == + c 90% jj 9m t AV? 32 9(2 ) 3.10 , (c) (1000 kg/m )(0.0003 m )(20 m/s) kg For the Example data Ans.=? 90% t3.0s 240 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.99 Let the rocket of Fig. E3.12 start at z = 0, with constant exit velocity and exit mass flow, and rise vertically with zero drag. (a) Show that, as long as fuel burning continues, the vertical height S(t) reached is given by 1??? ?=?+ =? [ln ], 1 eo o VM mt Swher mM (b) Apply this to the case Ve = 1500 m/s and Mo = 1000 kg to find the height reached after a burn of 30 seconds, when the final rocket mass is 400 kg. Solution: (a) Ignoring gravity effects, integrate the equation of the projectile?s velocity (from E3.12): 0 ? ??? ==?? ? ??? ??? ? ?? () () ln 1 t e o mt St Vt dt V dt M 1, , oo mt m Let then d dt and the becomes MM ??=? =? integral 1 ? ? ??? ??? ??? ? ?? ? ? ? ? =? = ? = ? + ?? ?? ?? ?? ? ? ? ? ? 1 () ( ) ( ln ) [ ln ] [ ln 1] oeo eo e MVM VM St V d mm m (b) Substituting the numerical values given, 1000 kg 400 kg (20 kg/s)(30 s) 20 kg/s 1 0.40 30 s 1000 kg fo MM M mad tt ? ? ?? == = = =? = ?? (1500 m/s)(1000 kg) ( 30 s) [0.4 ln(0.4) (0.4) 1] m (20 kg/s) St Ans.== ?+= 17,500 3.100 Suppose that the solid-propellant rocket of Prob. 3.35 is built into a missile of diameter 70 cm and length 4 m. The system weighs 1800 N, which includes 700 N of propellant. Neglect air drag. If the missile is fired vertically from rest at sea level, estimate (a) its velocity and height at fuel burnout and (b) the maximum height it will attain. Solution: The theory of Example 3.12 holds until burnout. Now Mo = 1800/9.81 = 183.5 kg, and recall from Prob. 3.35 that Ve = 1150 m/s and the exit mass flow is 11.8 kg/s. The fuel mass is 700/9.81 = 71.4 kg, so burnout will occur at tburnout = 71.4/11.8 = 6.05 s. Then Example 3.12 predicts the velocity at burnout: b 11.8(6.05) V 1150 ln 1 9.81(6.05) (a) 183.5 Ans. ?? =? ? ? ? ?? ?? m 507 s Chapter 3 ? Integral Relations for a Control Volume 241 Meanwhile, Prob. 3.99 gives the formula for altitude reached at burnout: 2 b 183.5(1150) 1 S [1 (0.611){ln(0.611) 1}] (9.81)(0.605) (a) 11.8 2 Ans.=+ ? ?1393 m where ?0.611? = 1 ? 11.8(6.05)/183.5, that is, the mass ratio at burnout. After burnout, with drag neglected, the missile moves as a falling body. Maximum height occurs at o V 507 t 51.7 s, whence g9.81 ?= = = 22 o 1 S S g t 1393 (1/2)(9.81)(51.7) (b) 2 Ans.=+?= + ?14500 m 3.101 Modify Prob. 3.100 by accounting for air drag on the missile F ? C?D 2 V 2 , where C ? 0.02, ? is the air density, D is the missile diameter, and V is the missile velocity. Solve numerically for (a) the velocity and altitude at burnout and (b) the maximum altitude attained. Solution: The CV vertical-momentum analysis of Prob. 3.100 is modified to include a drag force resisting the upward acceleration: 4.26 22 o eD o o o TBzdV m mV mg C D V , where m m mt, and dt T ??? ??? =?? =? = ?? ?? oeD kg m with numerical values m 183.5 kg, m 11.8 , V 1150 , D 0.7 m, C 0.02 ss ===== We may integrate this numerically, by Runge-Kutta or a spreadsheet or whatever, starting with V = 0, z = 0, at t = 0. After burnout, t ? 6.05 s, we drop the thrust term. The density is computed for the U.S. Standard Atmosphere from Table A-6. The writer?s numerical solution is shown graphically on the next page. The particular values asked for in the problem are as follows: At burnout, t 6.05 s: . (a)Ans= V 470 m/s, z 1370 m? ? At maximum altitude: (b)Ans. max t 40 s, z 8000 m? ? We see that drag has a small effect during rocket thrust but a large effect afterwards. 242 Solutions Manual ? Fluid Mechanics, Fifth Edition Problem 3.101 ? NUMERICAL SOLUTION 3.102 As can often be seen in a kitchen sink when the faucet is running, a high- speed channel flow (V1, h1) may ?jump? to a low-speed, low-energy condition (V2, h2) as in Fig. P3.102. The pressure at sections 1 and 2 is approximately hydrostatic, and wall friction is negligible. Use the continuity and momentum relations to find h2 and V2 in terms of (h1, V1). Fig. P3.102 Solution: The CV cuts through sections 1 and 2 and surrounds the jump, as shown. Wall shear is neglected. There are no obstacles. The only forces are due to hydrostatic pressure: x11221 11 2 2 11 F 0 gh (h b) gh (h b) m(V V ), 22 where m V h b V h b ?? ?? ?== ? = ? == 221 Solve for V and h /h ) .Ans 2 11 2 1 1 11 Vh /h 1 8V /(gh 22 ?+ + Chapter 3 ? Integral Relations for a Control Volume 243 3.103 Suppose that the solid-propellant rocket of Prob. 3.35 is mounted on a 1000-kg car to propel it up a long slope of 15°. The rocket motor weighs 900 N, which includes 500 N of propellant. If the car starts from rest when the rocket is fired, and if air drag and wheel friction are neglected, estimate the maximum distance that the car will travel up the hill. Solution: This is a variation of Prob. 3.100, except that ?g? is now replaced by ?g sin?.? Recall from Prob. 3.35 that the rocket mass flow is 11.8 kg/s and its exit velocity is 1150 m/s. The rocket fires for tb = (500/9.81)/11.8 = 4.32 sec, and the initial mass is Mo = (1000 + 900/9.81) = 1092 kg. Then the differential equation for uphill powered motion is eo dV mmVmgsin,mMmt dt ?=? =? eo This integrates to: V(t) V ln(1 mt/M ) gt sin for t 4.32 s.?=?? ? ? After burnout, the rocket coasts uphill with the usual falling-body formulas with ?g sin?.? The distance travelled during rocket power is modified from Prob. 3.99: 2 oe o o 1 S (MV/m)[1(1mt/M){ln(1mt/M)1}] gtsin 2 ?=+???? Apply these to the given data at burnout to obtain burnout 1 V 1150 ln(0.9533) (9.81)sin15 (4.32) m/s 2 =? ? ° ?44.0 2 burnout 1092(1150) 1 S [1 0.9533{ln(0.9533) 1}] (9.81)sin15 (4.32) 94 m 11.8 2 =+ ? °? The rocket then coasts uphill a distance ?S such that Vb 2 = 2g?S sin?, or ?S = (44.0) 2 /[2(9.81)sin 15°] ? 381 m. The total distance travelled is 381 + 94 ? 475 m Ans. 3.104 A rocket is attached to a rigid horizontal rod hinged at the origin as in Fig. P3.104. Its initial mass is Mo, and its exit properties are m and Ve relative to the rocket. Set up the differential equation for rocket motion, and solve for the angular velocity ?(t) of the rod. Neglect gravity, air drag, and the rod mass. Fig. P3.104 244 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: The CV encloses the rocket and moves at (accelerating) rocket speed ?(t). The rocket arm is free to rotate, there is no force parallel to the rocket motion. Then we have tangent rel e e o d F 0 a dm m( V ), or mR mV , where m M mt dt ? ?=? =? = =? ? Integrate, with 0 at t 0, to obtain .Ans ?? ?= = ? ?? ?? e o V mt ln 1 RM =? ? 3.105 Extend Prob. 3.104 to the case where the rocket has a linear air drag force F = cV, where c is a constant. Assuming no burnout, solve for ?(t) and find the terminal angular velocity, i.e., the final motion when the angular acceleration is zero. Apply to the case Mo = 6 kg, R = 3 m, m = 0.05 kg/s, Ve = 1100 m/s, and c = 0.075 N·s/m to find the angular velocity after 12 s of burning. Solution: If linear resistive drag is added to Prob. 3.104, the equation of motion becomes e o mVd m C , where m M mt, with 0 at t 0 dt R ? =?? =? ?== The solution is found by separation of variables: e o 00 ddt If B mV /R, then , or: . (a) BC M mt t Ans ? ?? ??? ??==?=? ?? ?? ? ?? ?? ?? C/m o Bmt 11 CM Strictly speaking, there is no terminal velocity, but if we set the acceleration equal to zero in the basic differential equation, we obtain an estimate ?term = mVe/(RC). Ans. (b) For the given data, at t = 12 s, we obtain the angular velocity 0.075 0.05(0.05)(1100) 0.05(12) At t 12 s: 1 1 . (c) (3.0)(0.075) 6.0 Ans ?? ?? ?? =?= ?? ? ?? ?? ?? rad 36 sec 3.106 Extend Prob. 3.104 to the case where the rocket has a quadratic air drag force F = kV 2 , where k is a constant. Assuming no burnout, solve for ?(t) and find the terminal angular velocity, i.e., the final motion when the angular acceleration is zero. Apply to the case Mo = 6 kg, R = 3 m, m = 0.05 kg/s, Ve = 1100 m/s, and k = 0.0011 N·s 2 /m 2 to find the angular velocity after 12 s of burning. Chapter 3 ? Integral Relations for a Control Volume 245 Solution: If quadratic drag is added to Prob. 3.104, the equation of motion becomes 2e o mVd m kR , where m M mt, with at t 0 dt R ? = ?? = ? ?=0 = The writer has not solved this equation analytically, although it is possible. A numerical solution results in the following results for this particular data (Ve = 1100 m/s, etc.): t, sec: 0 3 6 9 12 15 20 30 40 50 60 70 ?, rad/s: 0 9.2 18.4 27.3 35.6 43.1 53.5 66.7 72.0 73.9 74.4 74.5 The answer desired, ? ? 36 rad/s at t = 12 s, is coincidentally the same as Prob. 3.105. Note that, in this case, the quadratic drag, being stronger at high ?, causes the rocket to approach terminal speed before the fuel runs out (assuming it has that much fuel): e final 22 mVd 0.05(1100) Terminal speed, 0: . dt kR 0.0011(3) Ans ? =?= = = rad 74.5 s 3.107 The cart in Fig. P3.107 moves at constant velocity Vo = 12 m/s and takes on water with a scoop 80 cm wide which dips h = 2.5 cm into a pond. Neglect air drag and wheel friction. Estimate the force required to keep the cart moving. Fig. P3.107 Solution: The CV surrounds the cart and scoop and moves to the left at cart speed Vo. Momentum within the cart fluid is neglected. The horizontal force balance is x scoop inlet inlet o F Thrust m V , but V V (water motion relative to scoop)?=? =? = o Therefore Thrust mV [998(0.025)(0.8)(12)](12) Ans.== ? 2900 N 3.108 A rocket sled of mass M is to be decelerated by a scoop, as in Fig. P3.108, which has width b into the paper and dips into the water a depth h, creating an upward jet at 60°. The rocket thrust is T to the left. Let the initial velocity be Vo, and neglect air drag and wheel friction. Find an expression for V(t) of the sled for (a) T = 0 and (b) finite T ? 0. Fig. P3.108 246 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: The CV surrounds the sled and scoop and moves to the left at sled speed V(t). Let x be positive to the left. The horizontal force balance is x out out in in dV F T M m u m u m( V cos ) m( V), m bhV dt ???=? = ? =? ?? = 2 sled dV or: M T CV , C bh(1 cos ) dt ? ?=? = ? Whether or not thrust T = 0, the variables can be separated and integrated: ==? ?? o Vt 2 V0 dV C (a) T 0: dt, or: (a) MV Ans. o o V V 1CVt/M = + o Vt 2 V0 M dV (b) T > 0: dt, or: (b) TCV Ans.= ? ?? final VV tanh[t ]=+?? where 1/2 1/2 1 final of V [T/ bg(1 cos )] , [T bh(1 cos )] /M, tanh (V /V )?????? ? =? =? = This solution only applies when Vo < Vfinal, which may not be the case for a speedy sled. 3.109 Apply Prob. 3.108 to the following data: Mo = 900 kg, b = 60 cm, h = 2 cm, Vo = 120 m/s, with the rocket of Prob. 3.35 attached and burning. Estimate V after 3 sec. Solution: Recall from Prob. 3.35 that the rocket had a thrust of 13600 N and an exit mass flow of 11.8 kg/s. Then, after 3 s, the mass has only dropped to 900 ? 11.8(3) = 865 kg, so we can approximate that, over 3 seconds, the sled mass is near constant at about 882 kg. Compute the ?final? velocity if the rocket keeps burning: 1/2 1/2 final 13600 m V [T/{ bh(1 cos )}] 47.66 998(0.6)(0.02)(1 cos60 ) s ?? ?? =?= ? ?? ?° ?? Thus solution (b) to Prob. 3.108 does not apply, since Vo = 120 m/s > Vfinal. We therefore effect a numerical solution of the basic differential equation from Prob. 3.108: 22 o dV dV m M T bh(1 cos )V , or: 882 13600 5.988V , with V 120 dt dt s ??=? ? = ? = The writer solved this on a spreadsheet for 0 < t < 3 sec. The results may be tabulated: t, sec: 0.0 0.5 1.0 1.5 2.0 2.5 3.0 sec V, m/s: 120.0 90.9 75.5 66.3 60.4 56.6 53.9 m/s The sled has decelerated to 53.9 m/s, quite near its ?steady? speed of about 46 m/s. Chapter 3 ? Integral Relations for a Control Volume 247 3.110 The horizontal lawn sprinkler in Fig. P3.110 has a water flow rate of 4.0 gal/min introduced vertically through the center. Estimate (a) the retarding torque required to keep the arms from rotating and Fig. P3.110 (b) the rotation rate (r/min) if there is no re- tarding torque. Solution: The flow rate is 4 gal/min = 0.008912 ft 3 /s, and ? = 1.94 slug/ft 3 . The velocity issuing from each arm is Vo = (0.008912/2)/[(?/4)(0.25/12 ft) 2 ] ? 13.1 ft/s. Then: oo 2 VT (a) From Example 3.15, and, if there is no motion ( 0), R QR ?? ? =? = oo T QRV (1.94)(0.008912)(6/12)(13.1) . (a)Ans?== ?0.113 ft-lbf o no friction o 13.1 ft/s rad (b) If T 0, then V /R 26.14 . (b) 6/12 ft s Ans? == rev 250 min 3.111 In Prob. 3.60 find the torque caused around flange 1 if the center point of exit 2 is 1.2 m directly below the flange center. Solution: The CV encloses the elbow and cuts through flange (1). Recall from Prob. 3.60 that D1 = 10 cm, D2 = 3 cm, weight flow = 150 N/s, whence V1 = 1.95 m/s and V2 = 21.7 m/s. Let ?O? be in the center of flange (1). Then rO2 = ?1.2j and rO1 = 0. Fig. P3.60 The pressure at (1) passes through O, thus causes no torque. The moment relation is ?? ?== ×?×= ?×? ? ?? ?? OO O22 O11 150 kg M m[( ) ( )] [( 1.2 ) ( 16.6 13.9 )] 9.81 s TrVrV j i j =?? O or: 305 N m Ans.Tk 3.112 The wye joint in Fig. P3.112 splits the pipe flow into equal amounts Q/2, which exit, as shown, a distance Ro from the axis. Neglect gravity and friction. Find an expression for the torque T about the x axis required to keep the system rotating at angular velocity ?. Fig. P3.112 248 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: Let the CV enclose the junction, cutting through the inlet pipe and thus exposing the required torque T. If y is ?up? in the figure, the absolute exit velocities are upper o o o lower o o o Vcos Vsin R ; Vcos Vsin R? ???=++? =???Vij kV i j k where Vo = Q/(2A) is the exit velocity relative to the pipe walls. Then the moments about the x axis are related to angular momentum fluxes by ()() axis o upper o lower inlet inlet 22 ooo oo T(Q/2)(R) (Q/2)(R) Q( ) QQ RRV RRV Q(0) ??? ? ?== ×+ ?×? =???+? +? ? M i jV jV rV ik ik Each arm contributes to the torque via relative velocity (?Ro). Other terms with Vo cancel. ?=?= 2 o Final torque result: T QR .Ans 2 o mR ? 3.113 Modify Ex. 3.14 so that the arm starts up from rest and spins up to its final rotation speed. The moment of inertia of the arm about O is Io. Neglect air drag. Find d?/dt and integrate to determine ? (t), assuming ? = 0 at t = 0. Solution: The CV is shown. Apply clock- wise moments: o CS ( ) dm ( ) dm,??× = × ?? rel Mra rV 2 oo o d or: T I Q(R RV ), dt ? ???? = ? Fig. 3.14 View from above of a single arm of a rotating lawn sprinkler. 2 oo oo QRV TdQR or: dt I I ??? ? ? += Integrate this first-order linear differential equation, with ? = 0 at t = 0. The result is: Ans.? ?? ?? = ?? ?? ?? ?? 2 o QR t/I oo 2 VT 1e R QR ? ? ? ?? Chapter 3 ? Integral Relations for a Control Volume 249 3.114 The 3-arm lawn sprinkler of Fig. P3.114 receives 20°C water through the center at 2.7 m 3 /hr. If collar friction is neglected, what is the steady rotation rate in rev/min for (a) ? = 0°; (b) ? = 40°? Solution: The velocity exiting each arm is o 22 Q/3 2.7/[(3600)(3)] m V6.50 s( /4)d ( /4)(0.007)?? == = Fig. P3.114 With negligible air drag and bearing friction, the steady rotation rate (Example 3.15) is o final Vcos (6.50)cos0 rad (a) 0 : 43.3 . (a) R0.15 ms Ans ? ??? ° ==°=== rev 414 min o (b) cos (414)cos 40 . (b)Ans????=40°: = = °= rev 317 min 3.115 Water at 20°C flows at 30 gal/min through the 0.75-in-diameter double pipe bend of Fig. P3.115. The pressures are p1 = 30 lbf/in 2 and p2 = 24 lbf/in 2 . Compute the torque T at point B necessary to keep the pipe from rotating. Solution: This is similar to Example 3.13, of the text. The volume flow Q = 30 gal/min = 0.0668 ft 3 /s, and ? = 1.94 slug/ft 3 . Thus the mass flow ?Q = 0.130 slug/s. The velocity in the pipe is Fig. P3.115 12 2 0.0668 ft V V Q/A 21.8 s(/4)(0.75/12)? == = = If we take torques about point B, then the distance ?h1,? from p. 143, = 0, and h2 = 3 ft. The final torque at point B, from ?Ans. (a)? on p. 143 of the text, is ? =+= + ?? 2 B222 2 T h (p A mV ) (3 ft)[(24 psi) (0.75 in) (0.130)(21.8)] . 4 Ans40 ft lbf 250 Solutions Manual ? Fluid Mechanics, Fifth Edition Chapter 3 ? Integral Relations for a Control Volume 251 3.116 The centrifugal pump of Fig. P3.116 has a flow rate Q and exits the impeller at an angle ?2 relative to the blades, as shown. The fluid enters axially at section 1. Assuming incompressible flow at shaft angular velocity ?, derive a formula for the power P required to drive the impeller. Solution: Relative to the blade, the fluid exits at velocity Vrel,2 tangent to the blade, as shown in Fig. P3.116. But the Euler turbine formula, Ans. (a) from Example 3.14 of the text, 2t2 1t1 2t2 t1 Torque T Q(r V r V ) Qr V (assuming V 0) ? ? =? ?? Fig. P3.116 involves the absolute fluid velocity tangential to the blade circle (see Fig. 3.13). To derive this velocity we need the ?velocity diagram? shown above, where absolute exit velocity V2 is found by adding blade tip rotation speed ?r2 to Vrel,2. With trigonometry, t2 2 n2 2 n2 exit 22 Q V r V cot , where V Q/A is the normal velocity 2rb ?? ? =? = = With torque T known, the power required is P = T?. The final formula is: .Ans ???? ? ???? ???? 22 2 22 Q PQrr cot 2rb = ??? ? ? 3.117 A simple turbomachine is con- structed from a disk with two internal ducts which exit tangentially through square holes, as in the figure. Water at 20C enters the disk at the center, as shown. The disk must drive, at 250 rev/min, a small device whose retarding torque is 1.5 N?m. What is the proper mass flow of water, in kg/s? 252 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: This problem is a disguised version of the lawn-sprinkler arm in Example 3.15. For that problem, the steady rotating speed, with retarding torque To, was 2 , . oo o VT where V is the exit velocity and R is the arm radius R QR ? ? =? Enter the given data, noting that Q = 2Vo ?Lexit 2 is the total volume flow from the two arms: 22 21.5 mm 250 , 60 s 0.16 m s998(2 )(0.02 m) (0.16 m) o o o Vrad N solve V V ? ? ? ?? ==? = ?? ?? 6.11 The required mass flow is thus, 2 3 kg m 998 2 6.11 (0.02 m) . sm QAn? ?????? == = ?????? ?????? kg m24 s 3.118 Reverse the flow in Fig. P3.116, so that the system operates as a radial-inflow turbine. Assuming that the outflow into section 1 has no tangential velocity, derive an expression for the power P extracted by the turbine. Solution: The Euler turbine formula, ?Ans. (a)? from Example 3.14 of the text, is valid in reverse, that is, for a turbine with inflow at section 2 and outflow at section 1. The torque developed is o 2 t2 1 t1 2 t2 t1 TQ(rVrV)QrVifV0? ?= ?? ? The velocity diagram is reversed, as shown in the figure. The fluid enters the turbine at angle ?2, which can only be ensured by a guide vane set at that angle. The absolute tangential velocity component is directly related to inlet normal velocity, giving the final result t2 n2 2 n2 22 o Q VVcot,V , 2rb thus P T Ans. ? ? ? == ?? == ?? ?? ?? ? ? 22 22 Q Qr cot 2rb Chapter 3 ? Integral Relations for a Control Volume 253 3.119 Revisit the turbine cascade system of Prob. 3.78, and derive a formula for the power P delivered, using the angular- momentum theorem of Eq. (3.55). Solution: To use the angular momentum theorem, we need the inlet and outlet velocity diagrams, as in the figure. The Euler turbine formula becomes o1t12t2 t1t2 T Q(r V r V ) QR(V V )? ?=??? since the blades are at nearly constant radius R. From the velocity diagrams, we find t1 n1 t2 n2 n1 n2 1 V u V cot ; V u V cot , where V V V cos? ?? 12 =+ =? = = The normal velocities are equal by virtue of mass conservation across the blades. Finally, t1 t2 PQR(VV) ( ) .Ans? ?=?= + n1 2 QuV cot cot? ?? 3.120 A centrifugal pump delivers 4000 gal/min of water at 20°C with a shaft rotating at 1750 rpm. Neglect losses. If r1 = 6 in, r2 = 14 in, b1 = b2 = 1.75 in, Vt1 = 10 ft/s, and Vt2 = 110 ft/s, compute the absolute velocities (a) V1 and (b) V2, and (c) the ideal horsepower required. Solution: First convert 4000 gal/min = 8.91 ft 3 /s and 1750 rpm = 183 rad/s. For water, take ? = 1.94 slug/ft 3 . The normal velocities are determined from mass conservation: n1 n2 11 2 2 Q8.91 ft Qft V 19.5 ; V 8.34 2rb 2(6/12)(1.75/12) s 2rb s?? ? == = == Then the desired absolute velocities are simply the resultants of Vt and Vn: 221/2 221/ 12 V [(10) (19.45) ] V [(110) (8.3) ] . (a, b)Ans=+ = = + = ft ft 22 110 ss The ideal power required is given by Euler?s formula: 2t2 1t1 P Q (r V r V ) (1.94)(8.91)(183)[(14/12)(110) (6/12)(10)] ft-lbf 391,000 . (c) s Ans ? ?=?= ? =?710 hp 254 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.121 The pipe bend of Fig. P3.121 has D1 = 27 cm and D2 = 13 cm. When water at 20°C flows through the pipe at 4000 gal/ min, p1 = 194 kPa (gage). Compute the torque required at point B to hold the bend stationary. Solution: First convert Q = 4000 gal/ min = 0.252 m 3 /s. We need the exit velocity: Fig. P3.121 22 11 2 0.252 m m V Q/A 19.0 Meanwhile, V Q/A 4.4 ss(/4)(0.13)? == = == We don?t really need V1, because it passes through B and has no angular momentum. The angular momentum theorem is then applied to point B: BB 11 22 pA pA ( ) m( )?=+× +× ?= 12 2211 MTr j rirVrV× ?× But r1 and p2 are zero, B hence m( ) Q[(0.5 0.5 ) (19.0 )]?==+ 22 TrV ij i×× Thus, finally, TB = (998)(0.252)(0.5)(19.0)(?k) ? ?2400 k N · m (clockwise) Ans. 3.122 Extend Prob. 3.46 to the problem of computing the center of pressure L of the normal face Fn, as in Fig. P3.122. (At the center of pressure, no moments are required to hold the plate at rest.) Neglect friction. Express your result in terms of the sheet thickness h1 and the angle ? between the plate and the oncoming jet 1. Fig. P3.122 Solution: Recall that in Prob. 3.46 of this Manual, we found h2 = (h1/2)(1 + cos?) and that h3 = (h1/2)(1 ? cos?). The force on the plate was Fn = ?QVsin?. Take clockwise moments about O and use the angular momentum theorem: () ?? ? ?=?= + ? =+?=? |||||| on 2 z3 z1 z 22 2 22 3 3 2 3 MFLm m m Vh (h V/2) Vh ( h V/2) 0 (1/2) V h h 2O 2 3O 3 1O 1 rV rV rV××× Chapter 3 ? Integral Relations for a Control Volume 255 ( ) ( ) 22 2 2 2 23 23 2 11 (1/2)Vhh hh Thus L . 2h sinVhsin Ans ? ??? ?? =? = =? 1 1 h cot 2 ?? The latter result follows from the (h1, h2, h3) relations in 3.46. The C.P. is below point O. 3.123 The waterwheel in Fig. P3.123 is being driven at 200 r/min by a 150-ft/s jet of water at 20°C. The jet diameter is 2.5 in. Assuming no losses, what is the horse- power developed by the wheel? For what speed ? r/min will the horsepower developed be a maximum? Assume that there are many buckets on the waterwheel. Solution: First convert ? = 200 rpm = 20.9 rad/s. The bucket velocity = Vb = ?R = (20.9)(4) = 83.8 ft/s. From Prob. 3.51 of this Manual, if there are many buckets, the entire (absolute) jet mass flow does the work: Fig. P3.123 ? ? =??°= ? ?? ?? 4 ?? ? =? jet b jet b jet jet b jet b 2 P m V (V V )(1 cos165 ) A V V (V V )(1.966) 2.5 (1.94) (150)(83.8)(150 83.8)(1.966) 12 ft lbf 108200 . s Ans197 hp Prob. 3.51: Max. power is for Vb = Vjet/2 = 75 ft/s, or ? = 18.75 rad/s = 179 rpm Ans. 3.124 A rotating dishwasher arm delivers at 60°C to six nozzles, as in Fig. P3.124. The total flow rate is 3.0 gal/min. Each nozzle has a diameter of 3 16 in. If the nozzle flows are equal and friction is neglected, estimate the steady rotation rate of the arm, in r/min. Fig. P3.124 256 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: First we need the mass flow and velocity from each hole ?i,? i = 1 to 6: i ii 2 i Q (3.0/448.8)/6 ft Q 3/448.8 slug V 5.81 m 1.94 0.00216 As66 3/16 (/4) 12 ? ? ?? == ? = = = ?? ?? ?? ?? ?? Recall Example 3.15 from the text. For each hole, we need the absolute velocity, Vi ? ?ri. The angular momentum theorem is then applied to moments about point O: OO i inin ii i M T m ( ) m V m r (V cos40° r )?==? ? =? ?? iO i, abs rV× All the velocities and mass flows from each hole are equal. Then, if TO = 0 (no friction), ii i i i 22 ii i m r V cos 40 r 5.33 rad V cos40° (5.81)(0.766) 4.25 5.58 smr r Ans. ?°? ?= = = = = ?? 41 rpm 3.125 A liquid of density ? flows through a 90° bend as in Fig. P3.125 and issues vertically from a uniformly porous section of length L. Neglecting weight, find a result for the support torque M required at point O. Solution: Mass conservation requires i Fig. P3.125 L ww w 0 dQ QV(d)dxVdL,or: dV dx ?? ?== = ? Then the angular momentum theorem applied to moments about point O yields L O O out w w CS 0 L 222 w 0 ()dm (Rx)VdVdx dV [(R x) R ] 2 ?? ?? ?== = + =+? ?? | O MT rV× k k Substitute Vw? dL = Q and clean up to obtain Ow L QV R 2 ? ?? =+ ?? ?? Tk Ans. Chapter 3 ? Integral Relations for a Control Volume 257 3.126 Given a steady isothermal flow of water at 20°C through the device in Fig. P3.126. Heat-transfer, gravity, and temperature effects are negligible. Known data are D1 = 9 cm, Q1 = 220 m 3 /h, p1 = 150 kPa, D2 = 7 cm, Q2 = 100 m 3 /h, p2 = 225 kPa, D3 = 4 cm, and p3 = 265 kPa. Compute the rate of shaft work done for this device and its direction. Fig. P3.126 Solution: For continuity, Q3 = Q1 ? Q2 = 120 m 3 /hr. Establish the velocities at each port: 1 123 222 1 Q 220/3600 m 100/3600 m 120/3600 m V 9.61 ; V 7.22 ; V 26.5 As s s(0.045) (0.035) (0.02)??? == = = = = = With gravity and heat transfer and internal energy neglected, the energy equation becomes 2 22 33 22 11 sv3 2 1 32 pV pV pV QW W m m m , 222??? ?????? ??= + + + ? + ?????? ?????? s 2 100 225000 (7.22) 120 265000 (26.5) or: W / 3600 998 2 3600 998 2 220 150000 (9.61) 3600 998 2 ? ???? ?= + + + ???? ???? ?? ++ ?? ?? Solve for the shaft work: s W 998( 6.99 20.56 12.00)=?? + ?? 15500 W Ans. (negative denotes work done on the fluid) 3.127 A power plant on a river, as in Fig. P3.127, must eliminate 55 MW of waste heat to the river. The river conditions upstream are Q1 = 2.5 m 3 /s and T1 = 18°C. The river is 45 m wide and 2.7 m deep. If heat losses to the atmosphere and ground are negligible, estimate the downstream river conditions (Q0, T0). Fig. P3.127 258 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: For water, take cp ? 4280 J/kg · °C. For an overall CV enclosing the entire sketch, out p out in p in Qm(cT)m(cT),=? out out or: 55,000,000 W (998 2.5)[4280T 4280(18)], solve for T .Ans?× ? ?23.15 C° The power plant flow is ?internal? to the CV, hence out in QQ . .Ans== 3 2.5 m /s 3.128 For the conditions of Prob. 3.127, if the power plant is to heat the nearby river water by no more than 12°C, what should be the minimum flow rate Q, in m 3 /s, through the plant heat exchanger? How will the value of Q affect the downstream conditions (Qo, To)? Solution: Now let the CV only enclose the power plant, so that the flow going through the plant shows as an inlet and an outlet. The CV energy equation, with no work, gives plant out p out in p in plant in out Q m c T m c T (998)Q (4280)(12 C) since Q Q=?= ° = plant 55,000,000 Solve for Q . (998)(4280)(12) Ans=? 3 1.07 m /s It?s a lot of flow, but if the river water mixes well, the downstream flow is still the same. 3.129 Multnomah Falls in the Columbia River Gorge has a sheer drop of 543 ft. Use the steady flow energy equation to estimate the water temperature rise, in °F, resulting. Solution: For water, convert cp = 4200 × 5.9798 = 25100 ft·lbf/(slug·°F). Use the steady flow energy equation in the form of Eq. (3.66), with ?1? upstream at the top of the falls: 22 1112 22 Vgz Vgzqhh++=++? Assume adiabatic flow, q = 0 (although evaporation might be important), and neglect the kinetic energies, which are much smaller than the potential energy change. Solve for p12 32.2(543) cTg(z z),or: T . 25100 hAns?= ?? ? ?= ?0.70 ° Chapter 3 ? Integral Relations for a Control Volume 259 3.130 When the pump in Fig. P3.130 draws 220 m 3 /h of water at 20°C from the reservoir, the total friction head loss is 5 m. The flow discharges through a nozzle to the atmosphere Estimate the pump power in kW delivered to the water. Solution: Let ?1? be at the reservoir surface and ?2? be at the nozzle exit, as shown. We need to know the exit velocity: Fig. P3.130 22 1 2 220/3600 m V Q/A 31.12 , while V 0 (reservoir surface) s(0.025)? == = ? Now apply the steady flow energy equation from (1) to (2): 22 11 22 12fp pV pV zzh, g2g g2g?? ++=+++? 2 pp or: 0 0 0 0 (31.12) /[2(9.81)] 2 5 h , solve for h 56.4 m.++=+ ++? ? The pump power P = ?gQhp = (998)(9.81)(220/3600)(56.4) = 33700 W = 33.7 kW Ans. 3.131 When the pump in Fig. P3.130 delivers 25 kW of power to the water, the friction head loss is 4 m. Estimate (a) the exit velocity; and (b) the flow rate. Solution: The energy equation just above must now be written with V2 and Q unknown: 2 2 pp V P 25000 0000 24h,whereh 2g gQ (998)(9.81)Q? ++=+ ++? = = 2 2 Q and where V . Solve numerically by iteration: (0.025)? = V2 ? 28.1 m/s Ans. (a) and Q = (28.1)?(0.025) 2 ? 0.0552 m 3 /s ? 200 m 3 /hr Ans. (b) 260 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.132 Consider a turbine extracting energy from a penstock in a dam, as in the figure. For turbulent flow (Chap. 6) the friction head loss is hf = CQ 2 , where the constant C depends upon penstock dimensions and water physical properties. Show that, for a given penstock and river flow Q, the maximum turbine power possible is Pmax = 2?gHQ/3 and occurs when Q = (H/3C) 1/2 . Solution: Write the steady flow energy equation from point 1 on the upper surface to point 2 on the lower surface: 22 11 22 0 f turbine pV pV Hhh gg gg?? ++=++++ But p1 = p2 = patm and V1 ? V2 ? 0. Thus the turbine head is given by 2 , tf hHh HCQ=?=? 3 : t or Power P gQh gQH gCQ???== = ? Differentiate and set equal to zero for max power and appropriate flow rate: 2 30 . dP gH gCQ Ans dQ ??=? =if QH/3C= .Ans? ?? ?? ?? Insert Q in P to obtain max 2H PgQ 3 = 3.133 The long pipe in Fig. 3.133 is filled with water at 20°C. When valve A is closed, p1 ? p2 = 75 kPa. When the valve is open and water flows at 500 m 3 /h, p1 ? p2 = 160 kPa. What is the friction head loss between 1 and 2, in m, for the flowing condition? Fig. P3.133 Chapter 3 ? Integral Relations for a Control Volume 261 Solution: With the valve closed, there is no velocity or friction loss: 12 12 1221 p p p p 75000 z z , or: z z 7.66 m g g g 998(9.81)?? ? ? += + ?= = ? When the valve is open, the velocity is the same at (1) and (2), thus ?d? is not needed: 22 12 1 2 f12 p p V V 160000 With flow: h (z z ) 0 7.66 . g 2g 998(9.81) Ans ? ?? =+ +?= +??8.7 m 3.134 A 36-in-diameter pipeline carries oil (SG = 0.89) at 1 million barrels per day (bbl/day) (1 bbl = 42 U.S. gal). The friction head loss is 13 ft/1000 ft of pipe. It is planned to place pumping stations every 10 mi along the pipe. Estimate the horsepower which must be delivered to the oil by each pump. Solution: Since ?V and ?z are zero, the energy equation reduces to ff pft-losft h , and h 0.013 (10 mi) 5280 686 ft g ft-pipe mi? ? ?? == ? ?? ?? Convert the flow rate from 1E6 bbl/day to 29166 gal/min to 65.0 ft 3 /s. Then the power is ? ? =?= = = 5060 f ft lbf P Q p Qh (62.4)(65.0)(686) 2.78E6 . s Ans? hp 3.135 The pump-turbine system in Fig. P3.135 draws water from the upper reservoir in the daytime to produce power for a city. At night, it pumps water from lower to upper reservoirs to restore the situation. For a design flow rate of 15,000 gal/ min in either direction, the friction head loss is 17 ft. Estimate the power in kW (a) extracted by the turbine and (b) delivered by the pump. Fig. P3.135 262 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: (a) With the turbine, ?1? is upstream: 22 11 22 12ft pV pV zzh, g2g g2g?? ++=++++ t or: 0 0 150 0 0 25 17 h++ =+++= Solve for ht = 108 ft. Convert Q = 15000 gal/min = 33.4 ft 3 /s. Then the turbine power is ? ? == = ?410 hp turb ft lbf P Qh (62.4)(33.4)(108) 225,000 (a) s Ans. (b) For pump operation, point ?2? is upstream: 22 22 11 21fp pV pV zzh, g2g g2g?? ++=+++? p or: 0 0 25 0 0 150 17 h++ =++ + ? p Solve for h 142 ft? The pump power is Ppump = ? Qhp = (62.4)(33.4)(142) = 296000 ft·lbf/s = 540 hp. Ans. (b) 3.136 Water at 20°C is delivered from one reservoir to another through a long 8-cm- diameter pipe. The lower reservoir has a surface elevation z2 = 80 m. The friction loss in the pipe is correlated by the formula hloss ? 17.5(V 2 /2g), where V is the average velocity in the pipe. If the steady flow rate through the pipe is 500 gallons per minute, estimate the surface elevation of the higher reservoir. Solution: We may apply Bernoulli here, 2 12 17.5 2 f V hzz g ==? 2 3 1 2 2 17.5 (500 gal/min)(3.785 m /gal)(min/60s) 80 m 2(9.81 m/s ) (0.08 ) 4 z ? ?? ?? =? ?? Ans.z 1 115 m? Chapter 3 ? Integral Relations for a Control Volume 263 3.137 A fireboat draws seawater (SG = 1.025) from a submerged pipe and discharges it through a nozzle, as in Fig. P3.137. The total head loss is 6.5 ft. If the pump efficiency is 75 percent, what horsepower motor is required to drive it? Solution: For seawater, ? = 1.025(62.4) = 63.96 lbf/ft 3 . The energy equation becomes Fig. P3.137 22 11 22 12fp 2 p pV pV zzh, g2g g2g (120) or: 0 0 0 0 10 6.5 h 2(32.2) ?? ++=+++? ++=+ + + ? Solve for hp = 240 ft. The flow rate is Q = V2A2 = (120)(?/4)(2/12) 2 = 2.62 ft 3 /s. Then ? ? == = ?97 hp p pump Qh (63.96)(2.62)(240) ft lbf P 53600 efficiency 0.75 s Ans. 3.138 Students in the fluid mechanics lab at Penn State University use the device in the figure to measure the viscosity of water: a tank and a capillary tube. The flow is laminar and has negligible entrance loss, in which case Chap. 6 theory shows that hf = 32?LV/(?gd 2 ). Students measure water temperature with a thermometer and Q with a stopwatch and a graduated cylinder. Density is measured by weighing a known volume. (a) Write an expression for ? as a function of these variables. (b) Calculate ? for the following actual data: T = 16.5°C, ? = 998.7 kg/m 3 , d = 0.041 in, Q = 0.31 mL/s, L = 36.1 in, and H = 0.153 m. (c) Compare this ? with the published result for the same temperature. (d) Compute the error which would occur if one forgot to include the kinetic energy correction factor. Is this correction important here? 264 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: (a) Write the steady flow energy equation from top to bottom: 22 2 1 11 2 22 22 2 32 () 0,: ff p VpV LVV HL h or h HL gg gg ggd ?? ?? ?? ? +++=+++ = =+? Noting that, in a tube, Q = V? d 2 /4, we may eliminate V in favor of Q and solve for the fluid viscosity: (a)Ans. ?? ? ? ? ? =+? gd Q HL LQ L 4 2 () 128 16 (b) For the given data, converting d = 0.041 in = 0.00104 m, L = 36.1 in = 0.917 m, and Q = 0.31 mL/s = 3.1E?7 m 3 /s, we may substitute in the above formula (a) and calculate 4 (998.7)(9.81)(0.00104) 2.0(998.7)(3.1 7) (0.153 0.917) 128(0.917)(3.1 7) 16 (0.917) E E ? ? ? ? =+? ? 0.001063 0.000013 (b)Ans.=?? kg 0.00105 ms? (c) The accepted value (see Appendix Table A-1) for water at 16.5°C is ? ? 1.11E?3 kg/m·s, the error in the experiment is thus about ?5.5%. Ans. (c) (d) If we forgot the kinetic-energy correction factor ?2 = 2.0 for laminar flow, the calculation in part (b) above would result in 0.001063 0.000007 (negligible 0.6% error) (d)Ans.?=??0.001056 kg/m s? In this experiment, the dominant (first) term is the elevation change (H + L)?the momentum exiting the tube is negligible because of the low velocity (0.36 m/s). 3.139 The horizontal pump in Fig. P3.139 discharges 20°C water at 57 m 3 /h. Neglecting losses, what power in kW is delivered to the water by the pump? Solution: First we need to compute the velocities at sections (1) and (2): Fig. P3.139 12 22 Q 57/3600 m Q 57/3600 m V 2.49 ; V 22.4 AsAs(0.045) (0.015)?? == = == = Chapter 3 ? Integral Relations for a Control Volume 265 Then apply the steady flow energy equation across the pump, neglecting losses: 22 11 2 2 12fp pV pV zzh, g2g g2g?? ++=+++? 22 pp 120000 (2.49) 400000 (22.4) or: 0 0 0 h , solve for h 53.85 m 9790 2(9.81) 9790 2(9.81) + += + ++? ? pp 57 Then the pump power is P Qh 9790 (53.85) 8350 W 3600 Ans.? ?? == = = ?? ?? 8.4 kW 3.140 Steam enters a horizontal turbine at 350 lbf/in 2 absolute, 580°C, and 12 ft/s and is discharged at 110 ft/s and 25°C saturated conditions. The mass flow is 2.5 lbm/s, and the heat losses are 7 Btu/lb of steam. If head losses are negligible, how much horsepower does the turbine develop? Solution: We have to use the Steam Tables to find the enthalpies. State (2) is saturated vapor at 25°C = 77°F, for which we find h2 ? 1095.1 Btu/lbm ? 2.74E7 ft·lbf/slug. At state (1), 350 psia and 580°C = 1076°F, we find h1 ? 1565.3 Btu/lbm ? 3.92E7 ft·lbf/slug. The heat loss is 7 Btu/lbm ? 1.75E5 ft·lbf/slug. The steady flow energy equation is best written on a per-mass basis: 22 s2 21 1 11 qw h V h V,or:?=+ ?? 22 s s ft-lbf 1.75E5 w 2.74E7 (110) /2 3.92E7 (12) /2, solve for w 1.16E7 slug ??=+ ?? ? The result is positive because work is done by the fluid. The turbine power at 100% is ???? ?? == = ? ???? ?? ?? turb s 2.5 slug ft lbf ft lbf P mw 1.16E7 901000 32.2 s slug s Ans.1640 hp 3.141 Water at 20°C is pumped at 1500 gal/ min from the lower to the upper reservoir, as in Fig. P3.141. Pipe friction losses are approximated by hf ? 27V 2 /(2g), where V is the average velocity in the pipe. If the pump is 75 percent efficient, what horse- power is needed to drive it? Fig. P3.141 266 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: First evaluate the average velocity in the pipe and the friction head loss: 3 2 f 2 1500 ft Q 3.34 ft (17.0) Q 3.34 , so V 17.0 and h 27 448.8 s A s 2(32.2)(3/12)? == == = = ?121 ft Then apply the steady flow energy equation: 22 11 2 2 12fp p pV pV zzh, g2g g2g or: 0 0 50 0 0 150 121 h ?? ++=+++? ++ =++ + ? p ppump Qh (62.4)(3.34)(221) Thus h 221 ft, so P 0.75 ? ? === ? =? ft lbf 61600 . s Ans112 hp 3.142 A typical pump has a head which, for a given shaft rotation rate, varies with the flow rate, resulting in a pump performance curve as in Fig. P3.142. Suppose that this pump is 75 percent efficient and is used for the system in Prob. 3.141. Estimate (a) the flow rate, in gal/min, and (b) the horsepower needed to drive the pump. Fig. P3.142 Solution: This time we do not know the flow rate, but the pump head is hp ? 300 ? 50Q, with Q in cubic feet per second. The energy equation directly above becomes, 2 2 V 0 0 50 0 0 150 (27) (300 50Q), where Q V (0.5 ft) 2(32.2) 4 ? ++ =++ + ? ? = 23 This becomes the quadratic Q 4.60Q 18.4 0, solve for Q 2.57 ft /s+?= ? p pump Qh (62.4)(2.57)[300 50(2.57)] Then the power is P 0.75 ? ? ? == ? =? ft lbf 36700 . s Ans67 hp Chapter 3 ? Integral Relations for a Control Volume 267 3.143 The insulated tank in Fig. P3.143 is to be filled from a high-pressure air supply. Initial conditions in the tank are T = 20°C and p = 200 kPa. When the valve is opened, the initial mass flow rate into the tank is 0.013 kg/s. Assuming an ideal gas, estimate the initial rate of temperature rise of the air in the tank. Fig. P3.143 Solution: For a CV surrounding the tank, with unsteady flow, the energy equation is () 2 2 in shaft dpV ? e d m u gz Q W 0, neglect V /2 and gz dt 2 ?? ? ?? ?+++=?= ?? ?? ? vinpinv v ddTd Rewrite as ( c T) m c T c c T dt dt dt ? ?? ?? ??=+ where ? and T are the instantaneous conditions inside the tank. The CV mass flow gives ()in in dd dm0,or: m dt dt ? ?? ??= = ? Combine these two to eliminate ?(d?/dt) and use the given data for air: pv tank 3 v m(c c )T dT (0.013)(1005 718)(293) . 200000dt c (0.2 m )(718) 287(293) Ans ?? ? ? == ? ?? ?? ?? C 3.2 s ° 3.144 The pump in Fig. P3.144 creates a 20°C water jet oriented to travel a maxi- mum horizontal distance. System friction head losses are 6.5 m. The jet may be approximated by the trajectory of friction- less particles. What power must be deli- vered by the pump? Fig. P3.144 Solution: For maximum travel, the jet must exit at ? = 45°, and the exit velocity must be 1/2 2max2 [2(9.81)(25)] m V sin 2g z or: V 31.32 sin 45 s ? =? = ? ° The steady flow energy equation for the piping system may then be evaluated: 22 11 12 2 2fp p/ V/2g z p/ V/2g z h h ,??++=+++? 268 Solutions Manual ? Fluid Mechanics, Fifth Edition 2 pp or: 0 0 15 0 (31.32) /[2(9.81)] 2 6.5 h , solve for h 43.5 m++ =+ ++ ? ? 2 pump p Then P Qh (9790) (0.05) (31.32) (43.5) . 4 Ans ? ? ?? == ? ?? ?? 26200 W 3.145 The large turbine in Fig. P3.145 diverts the river flow under a dam as shown. System friction losses are hf = 3.5V 2 /(2g), where V is the average velocity in the supply pipe. For what river flow rate in m 3 /s will the power extracted be 25 MW? Which of the two possible solutions has a better ?conversion efficiency?? Fig. P3.145 Solution: The flow rate is the unknown, with the turbine power known: 22 11 22 12fturb fturb pV pV z z h h ,or:00500010h h 2g 2g?? ++=++++ ++=++++ 2 fpipe pp pie 2 pipe Q where h 3.5V /(2g) and h P /( Q) and V (/4)D ? ? == Introduce the given numerical data (e.g. Dpipe = 4 m, Ppump = 25E6 W) and solve: 3 3 Q 35410Q 2.261E6 0, with roots Q 76.5, 137.9, and 214.4 m /s?+= =++ ? The negative Q is nonsense. The large Q (=137.9) gives large friction loss, hf ? 21.5 m. The smaller Q (= 76.5) gives hf ? 6.6 m, about right. Select Qriver ? 76.5 m 3 /s. Ans. 3.146 Kerosene at 20°C flows through the pump in Fig. P3.146 at 2.3 ft 3 /s. Head losses between 1 and 2 are 8 ft, and the pump delivers 8 hp to the flow. What should the mercury-manometer reading h ft be? Solution: First establish the two velocities: 3 1 2 1 21 2.3 ft /s ( /4)(3/12 ft) ft 1 ft 46.9 ; 11.7 s4 s Q V A VV ? == === Fig. P3.146 Chapter 3 ? Integral Relations for a Control Volume 269 For kerosene take ? = 804 kg/m 3 = 1.56 slug/ft 3 , or ?k = 1.56(32.2) = 50.2 lbf/ft 3 . For mercury take ?m = 846 lbf/ft 3 . Then apply a manometer analysis to determine the pressure difference between points 1 and 2: 21 32 ( ) (846 50.2) 50.2 (5 ) 796 251 mk k lbf lbf pp h z h ft h ftft ?? ? ?? ?= ? ??= ? ? = ? ?? ?? Now apply the steady flow energy equation between points 1 and 2: ?? ? ? ++=+++? = = = 22 11 2 2 12 3 8(550) / , where 38.1 (50.2)(2.3 / ) fp p kk k pV pV P ftlbfs zzh h ft gg Qft s 22 12 21 2 (46.9) (11.7) Thus: 0 5 8 38.1 Solve 2866 50.2 2(32.2) 50.2 2(32.2) p pl ft p p ft ++=+++? ?= Now, with the pressure difference known, apply the manometer result to find h: 2 21 3 2866 251 / 2866 796 251, or: 796 / lbf ft p phh Ans. lbf ft + ?= = ? = =3.92 ft 3.147 Repeat Prob. 3.49 by assuming that p1 is unknown and using Bernoulli?s equation with no losses. Compute the new bolt force for this assumption. What is the head loss between 1 and 2 for the data of Prob. 3.49? Solution: Use Bernoulli?s equation with no losses to estimate p1 with ?z = 0: Fig. P3.49 22 1 1,ideal p (14) 15(144) (56) , solve for p 2(32.2) 62.4 2(32.2)? +?+ ?34.8 psia From the x-momentum CV analysis of Prob. 3.49, the bolt force is given by bolts 2,gage 2 2 1 22 FpAm(VV) (34.8 15)(144) (1 ft) 1.94 (1 ft) (14)(56 14) . 44 Ans ?? =?? ?? =? ? ?? ?? ?? 1340 lbf 270 Solutions Manual ? Fluid Mechanics, Fifth Edition We can estimate the friction head loss in Prob. 3.49 from the steady flow energy equation, with p1 taken to be the value of 38 psia given in that problem: 22 ff 38(144) (14) 15(144) (56) h, solve for h . 62.4 2(32.2) 62.4 2(32.2) Ans+=++ ?7.4 ft P3.148 Extend the siphon analysis of Ex. 3.22 as follows. Let p 1 = 1 atm and let the fluid be hot water at 60°C. Let z 1,2,4 be the same, with z 3 unknown. Find the value of z 3 for which the water might begin to vaporize. Solution: Given p 1 = 101350 Pa and recall that z 1 = 60 cm, z 2 = -25 cm, and z 4 was not needed. Then note that, because of steady-flow one-dimensional continuity, from Ex. 3.22, For cavitation, p 3 should drop down to the vapor pressure of water at 60°C, which from Table A.5 is 19.92 kPa. And, from Table A.3, the density of water at 60°C is 983 kg/m 3 . Now write Bernoulli from point 1 to point 3 at the top of the siphon: That?s pretty high, so the writer does not think cavitation is a problem with this siphon. ________________________________________________________________________ smzzgVV /08.4)]25.0(6.0)[81.9(2)(2 2123 =??=?== . 81.9 4.80 ,81.93.83.209.501.103 81.9 2 )/08.4( /983 19920 )6.0)(81.9( 2 0 983 101350 22 33 3 2 3 2 3 2 33 1 2 11 AnszSolvez z sm mkg Pa m gz Vp gz Vp m8.2=?++=++ ++=++ ++=++ ?? Chapter 3 ? Integral Relations for a Control Volume 271 3.149 A jet of alcohol strikes the vertical plate in Fig. P3.149. A force F ? 425 N is required to hold the plate stationary. Assuming there are no losses in the nozzle, estimate (a) the mass flow rate of alcohol and (b) the absolute pressure at section 1. Solution: A momentum analysis of the plate (e.g. Prob. 3.40) will give 222 222 2 F mV A V 0.79(998) (0.02) V 425 N, 4 solve for V 41.4 m/s ? ?== = = ? 2 whence m 0.79(998)( /4)(0.02) (41.4) (a)Ans.?=? 10.3 kg/s We find V1 from mass conservation and then find p1 from Bernoulli with no losses: 2 2 1221 2 Incompressible mass conservation: V V (D /D ) (41.4) 6.63 m/s 5 ?? ==? ?? ?? () 22 2 2 12 12 2 1 1 0.79(998) Bernoulli, z z : p p V V 101000 [(41.4) (6.63) ]?==+?=+ ? (b)Ans.? 760,000 Pa 3.150 An airfoil at an angle of attack ?, as in Fig. P3.150, provides lift by a Bernoulli effect, because the lower surface slows the flow (high pressure) and the upper surface speeds up the flow (low pressure). If the foil is 1.5 m long and 18 m wide into the paper, and the ambient air is 5000 m standard atmo- sphere, estimate the total lift if the average velocities on upper and lower surfaces are 215 m/s and 185 m/s, respectively. Neglect gravity. Fig. P3.150 272 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: A vertical force balance gives, () ?=? = ? =? == 22 22 1 () () 2 1 (0.7361)(215 185 )(18)(1.5) 2 119,250 Lift l u planform u l FppA VVbL NAns.119 kN Chapter 3 ? Integral Relations for a Control Volume 273 3.151 Water flows through a circular nozzle, exits into the air as a jet, and strikes a plate. The force required to hold the plate steady is 70 N. Assuming frictionless one- dimensional flow, estimate (a) the velocities at sections (1) and (2); (b) the mercury man- ometer reading h. Solution: (a) First examine the momen- tum of the jet striking the plate, 2 22in in F Fmu AV??==? =? Fig. P3.151 ? ?? =? ?? ?? 22 2 70 (998) (0.03 )( ) (a) 4 NVAns.V 2 9.96 m/s= ? ? ?? ?? ?? == 2 22 1 2 1 (9.96) (0.03 ) 4 (a) (0.1 ) 4 VA Then V or Ans. A V 1 0.9 m/s= (b) Applying Bernoulli, () 22 2 2 21 2 1 11 (998)(9.96 0.9 ) 49,100 22 p pVV Pa??= ? = ? = And from our manometry principles, ? ? == ? ? 49,100 (b) (133,100 9790) p hAns. g 0.4 m 3.152 A free liquid jet, as in Fig. P3.152, has constant ambient pressure and small losses; hence from Bernoulli?s equation z + V 2 /(2g) is constant along the jet. For the fire nozzle in the figure, what are (a) the minimum and (b) the maximum values of ? for which the water jet will clear the corner of the building? For which case will the jet velocity be higher when it strikes the roof of the building? Fig. P3.152 274 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: The two extreme cases are when the jet just touches the corner A of the building. For these two cases, Bernoulli?s equation requires that 2222 11 AAA A ft V 2gz (100) 2g(0) V 2gz V 2(32.2)(50), or: V 82.3 s += + =+=+ = The jet moves like a frictionless particle as in elementary particle dynamics: 2 11 1 Vertical motion: z V sin t gt ; Horizontal motion: x V cos t 2 ? ?=? = Eliminate ?t? between these two and apply the result to point A: 22 A AA 22 22 1 gx (32.2)(40) z 50 x tan 40 tan ; clean up and rearrange: 2V cos 2(100) cos ?? ?? == ? = ? 2 tan 1.25 0.0644 sec , solve for . (a) and . (b)Ans Ans???=+ =85.94 55.40°° Path (b) is shown in the figure, where the jet just grazes the corner A and goes over the top of the roof. Path (a) goes nearly straight up, to z = 155 ft, then falls down to pt. A. 3.153 For the container of Fig. P3.153 use Bernoulli?s equation to derive a formula for the distance X where the free jet leaving horizontally will strike the floor, as a function of h and H. For what ratio h/H will X be maximum? Sketch the three trajectories for h/H = 0.4, 0.5, and 0.6. Solution: The velocity out the hole and the time to fall from hole to ground are given by ofal V 2g( ) t 2h/gHh=? = Then the distance travelled horizontally is == ? ofal XVt Ans.2h(H h) Fig. P3.153 Chapter 3 ? Integral Relations for a Control Volume 275 Maximum X occurs at h = H/2, or Xmax = H. When h = 0.25H or 0.75H, the jet travels out to H = 0.866H. These three trajectories are shown in the sketch on the previous page. P3.154 Water at 20°C, in the pressurized tank of Fig. P3.154, flows out and creates a vertical jet as shown. Assuming steady frictionless flow, determine the height H to which the jet rises. Solution: This is a straightforward Bernoulli problem. Let the water surface be (1), the exit plane be (2), and the top of the vertical jet be (3). Let z 2 = 0 for convenience. If we are clever, we can bypass (2) and write Bernoulli directly from (1) to (3): If we took an intermediate step from (1) to (2), we would find V 2 2 /2g = 8.51 m, and then going from (2) to (3) would convert the velocity head into pure elevation, because V 3 = 0. 85 cm H ? Air 75 kPa-gage water Fig. P3.154 (1) (2) (3) .85.066.7 0085.0_0 )998)(81.9( 75000 :o, 22 3 2 33 1 2 11 AnsmmHSolve Hm rz g V g p z g V g p m8.51=+= ++=+ ++=++ ?? 276 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.155 Bernoulli?s 1738 treatise Hydro- dynamica contains many excellent sketches of flow patterns. One, however, redrawn here as Fig. P3.155, seems physically misleading. What is wrong with the drawing? Solution: If friction is neglected and the exit pipe is fully open, then pressure in the closed ?piezometer? tube would be atmospheric and the fluid would not rise at all in the tube. The open jet coming from the hole in the tube would have V ? ?(2gh) and would rise up to nearly the same height as the water in the tank. Fig. P3.155 P3.156 Extend Prob. 3.13 as follows. (a) Use Bernoulli?s equation to estimate the elevation of the water surface above the exit of the bottom cone. (b) Then estimate the time required for the water surface to drop 20 cm in the cylindrical tank. If you fail to solve part (a), assume that the initial elevation above the exit is 52 cm. Neglect the possible contraction and nonuniformity of the exit jet mentioned in Ex. 3.21. Solution: This is a ?Torricelli? flow, like Ex. 3.21. Using the continuity relation in Prob. 3.tank, we found that V ? 3.2 m/s. (a) Thus we know everything except ?z = h cyl + h cone : (b) The time ?t to drop from 52 cm to 32 cm could be obtained by numerical quadrature, or, better, we could solve for ?t analytically: ________________________________________________________________________ ).(52.0forsolve,)/81.9(2/2.32 2 aAnsmzzsmsmzgV cm52==??=??= ).( 03.0 2.0 )81.9(2 3108.0 )( 2 )32.052.0(2 :Result )(2 )( :integrate&Separate )( 44 2 4 ) 4 ( 4 22 0 2 32.0 52.0 22222 )( bAnst cm cm D D g t dt D D g z zd dt zd D dt dh DzgDhD dt d VDQ exit t exit exitexitout s3.12=?== ? =? ?= ? ? ? =?=?=?== ?? ? ????? Chapter 3 ? Integral Relations for a Control Volume 277 3.157 The manometer fluid in Fig. P3.157 is mercury. Estimate the volume flow in the tube if the flowing fluid is (a) gasoline and (b) nitrogen, at 20°C and 1 atm. Solution: For gasoline (a) take ? = 1.32 slug/ft 3 . For nitrogen (b), R ? 297 J/kg ? °C and ? = p/RT = (101350)/[(297)(293)] ? 1.165 kg/m 3 = 0.00226 slug/ft 3 . For mercury, take Fig. P3.157 ? ? 26.34 slug/ft 3 . The pitot tube (2) reads stagnation pressure, and the wall hole (1) reads static pressure. Thus Bernoulli?s relation becomes, with ?z = 0, 2 112 121 1 pVp,orV2(pp)/ 2 ? ?+= =? The pressure difference is found from the manometer reading, for each fluid in turn: 2 Hg (a) Gasoline: p ( ) (26.34 1.32)(32.2)(1/12 ft) 67.1 lbf/ft?????= ? = ? ? 2 1/2 111 ft 3 V [2(67.1)/1.32] 10.1 , Q V A (10.1) (a) s41 Ans. ? ??? ? ==== = ??? ? ??? ? 3 ft 0.495 s 2 2Hg (b) N : p ( )gh (26.34 0.00226)(32.2)(1/12) 70.7 lbf/ft???= ? = ? ? 2 1/2 111 ft 3 V [2(70.7)/0.00226] 250 , Q V A (250) (b) s41 Ans. ? ??? ? ====? ??? ? ??? ? 3 ft 12.3 s 278 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.158 In Fig. P3.158 the flowing fluid is CO2 at 20°C. Neglect losses. If p1 = 170 kPa and the manometer fluid is Meriam red oil (SG = 0.827), estimate (a) p2 and (b) the gas flow rate in m 3 /h. Solution: Estimate the CO2 density as ? = p/RT = (170000)/[189(293)] ? 3.07 kg/m 3 . The manometer reading gives the down- stream pressure: Fig. P3.158 2 12 oil CO p p ( )gh [0.827(998) 3.07](9.81)(0.08) 645 Pa? ??= ? = ? ? 2 Hence p 170,000 645 (a)Ans.=??169400Pa Now use Bernoulli to find V2, assuming p1 ? stagnation pressure (V1 = 0): 22 122 11 p(0)pV, 22 ??+?+ 12 2 2(p p ) 2(645) m or: V 20.5 3.07 s? ? ==? 23 22 Then Q V A (20.5)( /4)(0.06) 0.058 m /s (b)Ans.?== = ? 3 m 209 hr P3.159 The cylindrical water tank in Fig. P3.159 is being filled at a volume flow Q 1 = 1.0 gal/min, while the water also drains from a bottom hole of diameter d = 6 mm. At time t = 0, h = 0. Find (a) an expression for h(t) and (b) the eventual maximum water depth h max . Assume that Bernoulli?s steady-flow equation is valid. V 2 Q 1 h Fig. P3.159 diameter D = 20 cm CV Chapter 3 ? Integral Relations for a Control Volume 279 Solution: Bernoulli predicts that V 2 ? ?(2gh). Convert Q 1 = 6.309E-5 m 3 /s. A control volume around the tank gives the mass balance: Rearrange, separate the variables, and integrate: (a) The integration is a bit tricky and laborious. Here is the writer?s result: (a) A graph of h versus t for the particular given data is as follows: 0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0.2 0.22 0.24 0.26 0 200 400 600 800 1000 1200 h, meters t, sec (b) The water level rises fast and then slower and is asymptotic to the value h max = 0.254 m. This is when the outflow through the hole exactly equals the inflow from the pipe: 2 2 2 21 4 and 4 where,2)(0| dADAghAQAh dt d dt dm system ?? ==+?== ?? = ? tth dt A ghAQ dh 0 )( 0 21 1 2 ).( )81.9(2)006.0( 4 5309.6:,2 max max 2 3 max21 bAnshforSolve hm s m EorghAQ m0.254= =?= ? ).(2where, 2 )ln( 2 2 1 1 2 1 aAnsgA hA hQ QAQ t =? ? = ? ? ?? 280 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.160 The air-cushion vehicle in Fig. P3.160 brings in sea-level standard air through a fan and discharges it at high velocity through an annular skirt of 3-cm clearance. If the vehicle weighs 50 kN, estimate (a) the required airflow rate and (b) the fan power in kW. Solution: The air inside at section 1 is nearly stagnant (V ? 0) and supports the weight and also drives the flow out of the interior into the atmosphere: Fig. P3.160 22 1 o1 o1 atm exit exit 2 weight 50,000 N 1 1 p p : p p V (1.205)V 1768 Pa area 2 2(3 m) ? ? ??== == ? 3 exit e e e m Solve for V 54.2 m/s, whence Q A V (6)(0.03)(54.2) 30.6 s ??=== Then the power required by the fan is P = Qe?p = (30.6)(1768) ? 54000 W Ans. 3.161 A necked-down section in a pipe flow, called a venturi, develops a low throat pressure which can aspirate fluid upward from a reservoir, as in Fig. P3.161. Using Bernoulli?s equation with no losses, derive an expression for the velocity V1 which is just sufficient to bring reservoir fluid into the throat. Fig. P3.161 Solution: Water will begin to aspirate into the throat when pa ? p1 = ?gh. Hence: 222 1221 1 1atm 2 11 Volume flow: V V (D /D ) ; Bernoulli ( z 0): p V p V 22 ? ?=?=+?+ Chapter 3 ? Integral Relations for a Control Volume 281 42 2 a1 2 1 D Solve for p p ( 1)V gh, , or: 2D Ans. ? ????= ? ? = 2 4 2gh V 1 ? ?? ,Similarly Ans. 2 1, min 2, min 4 12 2gh V 1(D/D) ? V== ? 3.162 Suppose you are designing a 3 × 6-ft air-hockey table, with 1/16-inch-diameter holes spaced every inch in a rectangular pattern (2592 holes total), the required jet speed from each hole is 50 ft/s. You must select an appropriate blower. Estimate the volumetric flow rate (in ft 3 /min) and pressure rise (in psi) required. Hint: Assume the air is stagnant in the large manifold under the table surface, and neglect frictional losses. Solution: Assume an air density of about sea-level, 0.00235 slug/ft 3 . Apply Bernoulli?s equation through any single hole, as in the figure: ? ? +=+ 22 11 ,: ajet p Vp V or 22 1 2 0.00235 (50) 2.94 required a jet lbf p pp V Ans. ft ? ?=?== = = 2 lbf 0.0204 in The total volume flow required is 2 1 3 1/16 (# ) 50 (2592 ) 412 2.76 hole ft Q VA of holes ft holes s ft Ans. s ? ? ??? ? == ??? ? ??? ? == 3 ft 166 min It wasn?t asked, but the power required would be P = Q ?p = (2.76 ft 3 /s)(2.94 lbf/ft 2 ) = 8.1 ft·lbf/s, or about 11 watts. 282 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.163 The liquid in Fig. P3.163 is kerosine at 20°C. Estimate the flow rate from the tank for (a) no losses and (b) pipe losses hf ? 4.5V 2 /(2g). Solution: For kerosine let ? = 50.3 lbf/ft 3 . Let (1) be the surface and (2) the exit jet: Fig. P3.163 22 2 12 12 f21f VV V pp z z h , with z 0 and V 0, h K 2g 2g 2g?? ++=+++ = ? = 2 2 12 1 V p p (20 14.7)(144) Solve for (1 K) z 5 20.2 ft 2g 50.3? ?? +=+ =+ ? We are asked to compute two cases (a) no losses; and (b) substantial losses, K ? 4.5: 1/2 2 2 2(32.2)(20.2) ft 1 (a) K 0: V 36.0 , Q 36.0 . (a) 10 s 412 Ans ? ?? ?? == = = ? ?? ?? + ?? ?? 3 ft 0.197 s 2 2 2(32.2)(23.0) ft 1 (b) K 4.5: V 16.4 , Q 16.4 (b) 14.5 s 412 Ans. ? ?? == = = ? ?? + ?? 3 ft 0.089 s 3.164 An open water jet exits from a nozzle into sea-level air, as shown, and strikes a stagnation tube. If the centerline pressure at section (1) is 110 kPa and losses are neglected, estimate (a) the mass flow in kg/s; and (b) the height H of the fluid in the tube. Fig. P3.164 Solution: Writing Bernoulli and continuity between pipe and jet yields jet velocity: 4 4 22 1 1 998 4 1 110000 101350 1 , 2 jet ajet jet D pp V V D ? ?? ? ? ?? ?? ???= ? =?= ? ? ? ?? ?? ?? ?? ? ? ? ? ?? m s jet solve V = 4.19 2 998 (0.04) (4.19) (a) 4 jet jet Then the mass flow is A V Ans. ? ?== = kg m 5.25 s Chapter 3 ? Integral Relations for a Control Volume 283 (b) The water in the stagnation tube will rise above the jet surface by an amount equal to the stagnation pressure head of the jet: 2 2 (4.19) 0.02 m 0.02 0.89 (b) 229.81) jet jet V R Ans. g =+= + =+=H091m 3.165 A venturi meter, shown in Fig. P3.165, is a carefully designed constriction whose pressure difference is a measure of the flow rate in a pipe. Using Bernoulli?s equation for steady incompressible flow with no losses, show that the flow rate Q is related to the manometer reading h by 2 4 21 2( ) 1( / ) M Agh Q DD ? ? ? ? = ? where ?M is the density of the manometer fluid. Fig. P3.165 Solution: First establish that the manometer reads the pressure difference between 1 and 2: 12 M pp ( )gh? ?? =? (1) Then write incompressible Bernoulli?s equation and continuity between (1) and (2): 22 12 2 12 2112 11 22 VV pp (z 0): and V V(D/D), Q AV AV 22?? ?= + ? + = = = 212 Eliminate V and (p p ) from (1) above: .Ans? 2M 4 21 A 2gh( )/ Q 1(D/D) ? = ? ??? 3.166 A wind tunnel draws in sea-level standard air from the room and accelerates it into a 1-m by 1-m test section. A pressure transducer in the test section wall measures ?p = 45 mm water between inside and outside. Estimate (a) the test section velocity in mi/hr; and (b) the absolute pressure at the nose of the model. 284 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: (a) First apply Bernoulli from the atmosphere (1) to (2), using the known ?p: 322 a2 2 a 1 1 2 2 p p 45 mm H O 441 Pa; 1.225 kg/m ; p V p V 22 ? ? ??= = = + ?+ 11a 2 2 p 2(441) m Since V 0 and p p , we obtain V 26.8 . (a) 1.225 s Ans ? ? ?= ==== mi 60 hr (b) Bernoulli from 1 to 3: both velocities = 0, so pnose = pa ? 101350 Pa. Ans. (b) 3.167 In Fig. P3.167 the fluid is gasoline at 20°C at a weight flux of 120 N/s. Assuming no losses, estimate the gage pressure at section 1. Solution: For gasoline, ? = 680 kg/m 3 . Compute the velocities from the given flow rate: Fig. P3.167 3 12 22 W 120 N/s m Q 0.018 , g 680(9.81) s 0.018 m 0.018 m V 3.58 ; V 9.16 ss(0.04) (0.025) ? ?? == = == = = Now apply Bernoulli between 1 and 2: 22 22 12 12 1 12 VV p p p (3.58) 0(gage) (9.16) gz gz , or: 0 9.81(12) 2 2 2 680 2?? ? ++?++ + +? + + 1 Solve for p Ans.?104,000 Pa (gage) Chapter 3 ? Integral Relations for a Control Volume 285 3.168 In Fig. P3.168 both fluids are at 20°C. If V1 = 1.7 ft/s and losses are ne- glected, what should the manometer reading h ft be? Solution: By continuity, establish V2: 22 2112 ft V V (D /D ) 1.7(3/1) 15.3 s === Now apply Bernoulli between 1 and 2 to establish the pressure at section 2: 22 111222 p V gz p V gz , ? ? ??++=++ Fig. P3.168 22 1 1 or: p (1.94/2)(1.7) 0 0 (1.94/2)(15.3) (62.4)(10), p 848 psf++?+ + = This is gage pressure. Now the manometer reads gage pressure, so 1 a merc water 2 lbf p p 848 ( )gh (846 62.4)h, solve for h . ft Ans???= = ? = ? ?1.08 ft P3.169 Extend the siphon analysis of Ex. 3.22 to account for friction in the tube, as follows. Let the friction head loss in the tube be correlated as 5.4(V tube ) 2 /(2g), which approximates turbulent flow in a 2-m-long tube. Calculate the exit velocity in m/s and the volume flow rate in cm 3 /s. We repeat the sketch of Ex. 3.22 for convenience. Solution: Write the steady flow energy equation from the water surface (1) to the exit (2): z 1 = 60 cm z 2 = ? 25 cm cm z 4 V 2 ? Fig. E3.22 z = 0 d = 1 cm water g V hhz g V g p z g V g p tube ff 2 4.5where, 22 2 2 2 22 1 2 11 =+++=++ ?? 286 Solutions Manual ? Fluid Mechanics, Fifth Edition The tube area is constant, hence V tube = V 2 . Also, p 1 = p 2 and V 1 ? 0. Thus we obtain Tube friction has reduced the flow rate by more than 60%. 3.170 If losses are neglected in Fig. P3.170, for what water level h will the flow begin to form vapor cavities at the throat of the nozzle? Solution: Applying Bernoulli from (a) to (2) gives Torricelli?s relation: V2 = ?(2gh). Also, 22 1221 2 2 V V (D /D ) V (8/5) 2.56V=== Fig. P3.170 Vapor bubbles form when p1 reaches the vapor pressure at 30°C, pvap ? 4242 Pa (from Table A.5), while ? ? 996 kg/m 3 at 30°C (Table A.1). Apply Bernoulli between 1 and 2: 22 22 12 12 2 2 12 VV p p 4242 (2.56V ) 100000 V gz gz , or: 0 0 2 2 996 2 996 2?? ++?++ + +? ++ 2 2 Solve for V 34.62 2gh, or h 34.62/[2(9.81)] .Ans== = ?1.76 m .000167.0)01.0( 4 )61.1( . 4.51 )85.0)(/81.9(2 )4.51( 2 85.0)25.0(6.0 3 2 22 2 2 2 2 21 Ans s m m s m AVQand Ans msm VSolve g V mmmzz s cm 127 s m 1.61 3 ==== = + = +==??=? ? Chapter 3 ? Integral Relations for a Control Volume 287 3.171 For the 40°C water flow in Fig. P3.171, estimate the volume flow through the pipe, assuming no losses; then explain what is wrong with this seemingly innocent question. If the actual flow rate is Q = 40 m 3 /h, compute (a) the head loss in ft and (b) the constriction diameter D which causes cavitation, assuming that the throat divides the head loss equally and that changing the constriction causes no additional losses. Fig. P3.171 Solution: Apply Bernoulli between 1 and 2: 22 12 12 VV pp z z,or:00250010,or: 2g 2g?? ++?++ ++?++ 25 10 ??= This is madness, what happened? The answer is that this problem cannot be free of losses. There is a 15-m loss as the pipe-exit jet dissipates into the downstream reservoir. Ans. (a) (b) Examining analysis (a) shows that the head loss is 15 meters. For water at 40°C, the vapor pressure is 7375 Pa (Table A.5), and the density is 992 kg/m 3 (Table A.1). Now write Bernoulli between (1) and (3), assuming a head loss of 15/2 = 7.5 m: 22 13 31 13f,toal3 22 3 VV pp g Q 40/3600 0.0141 gz gz h , where V 2 A(/4)D D?? ? ++=+++ == = 22 101350 7375 (0.0141/D ) Thus 0 9.81(25) 0 (9.81)(7.5) 992 992 2 ++ ? + ++ 44 Solve for D 3.75E 7 m , or D Ans.?? ?0.0248 m 25 mm? This corresponds to V3 ? 23 m/s. 288 Solutions Manual ? Fluid Mechanics, Fifth Edition 3.172 The 35°C water flow of Fig. P3.172 discharges to sea-level standard atmosphere. Neglecting losses, for what nozzle diameter D will cavitation begin to occur? To avoid cavitation, should you increase or decrease D from this critical value? Solution: At 35°C the vapor pressure of water is approximately 5600 Pa (Table A.5). Bernoulli from the surface to point 3 gives the Fig. P3.172 Torricelli result V3 = ?(2gh) = ?2(32.2)(6) ? 19.66 ft/s. We can ignore section 2 and write Bernoulli from (1) to (3), with p1 = pvap and ?z = 0: 22 2 2 12 1 3 12 2 13 VV V V p p 117 2116 ,or: , 2 2 1.93 2 1.93 2 D but also V V 1/12 ?? +?+ +? + ?? = ?? ?? 4 13 ft Eliminate V and introduce V 19.66 to obtain D 3.07E 4, . s Ans==?D 0.132 ft? To avoid cavitation, we would keep D < 0.132 ft, which will keep p1 > pvapor. Chapter 3 ? Integral Relations for a Control Volume 289 3.173 The horizontal wye fitting in Fig. P3.173 splits the 20°C water flow rate equally, if Q1 = 5 ft 3 /s and p1 = 25 lbf/in 2 (gage) and losses are neglected, estimate (a) p2, (b) p3, and (c) the vector force required to keep the wye in place. Solution: First calculate the velocities: Fig. P3.173 123 22 1 Q5.0 ft 2.5 ft ft V 25.46 ; V 50.93 , V 28.65 As ss( /4)(6/12) ( /4)(3/12)?? == = = = = Then apply Bernoulli from 1 to 2 and then again from 1 to 3, assuming ?z ? 0: () 22 2 2 21 1 2 1.94 p p V V 25(144) [(25.46) (50.93) ] . (a)Ans ? =+ ? = + ? ?1713 psfg 22 2 2 31 1 3 1.94 p p (V V ) 25(144) [(25.46) (28.65) ] . (b)Ans ? =+ ? = + ? 3433 psfg? (c) to compute the support force R (see figure above), put a CV around the entire wye: xx1122 33 22 33 11 F R p A p A sin30 p A sin50 Q V sin30 Q V sin50 Q V R 707 42 229 124 106 247, or: R (to left) . (c)Ans ? ??? = + ? °? °= °+ °? =+?? =+? =?453 lbf yy22 33 22 33 F R p A cos30 p A cos50 Q V cos30 Q ( V )cos50 R 73 193 214 89, or: R (up) . (c)Ans ???=? °+ °= °+ ? ° =?+= ? ?5lbf+ 3.174 In Fig. P3.174 the piston drives water at 20°C. Neglecting losses, estimate the exit velocity V2 ft/s. If D2 is further constricted, what is the maximum possible value of V2? Solution: Find p1 from a freebody of the piston: Fig. P3.174 xa11 1a 22 10.0 lbf lbf F F p A p A , or: p p 28.65 ( /4)(8/12) ft? ?=+ ? ?= ? 290 Solutions Manual ? Fluid Mechanics, Fifth Edition Now apply continuity and Bernoulli from 1 to 2: 22 12 a1 11 2 2 1 2 VV p1p VA VA , or V V; 422?? ==+?+ 2 1a 1 2 2 2(28.65) Introduce p p and substitute for V to obtain V , 1.94(1 1/16) V .Ans ?= ? = ft 5.61 s If we reduce section 2 to a pinhole, V2 will drop off slowly until V1 vanishes: 2 2(28.65) Severely constricted section 2: V . 1.94(1 0) Ans=? ? ft 5.43 s 3.175 If the approach velocity is not too high, a hump in the bottom of a water channel causes a dip ?h in the water level, which can serve as a flow measurement. If, as shown in Fig. P3.175, ?h = 10 cm when the bump is 30 cm high, what is the volume flow Q1 per unit width, assuming no losses? In general, is ?h proportional to Q1? Fig. P3.175 Solution: Apply continuity and Bernoulli between 1 and 2: 22 12 11 2 2 1 2 VV V h V h ; h h H, solve . 2g 2g Ans=+?++ 2 1 22 12 2g h V (h /h ) 1 ? ? ? We see that ?h is proportional to the square of V1 (or Q1), not the first power. For the given numerical data, we may compute the approach velocity: 21 2 2(9.81)(0.1) m h 2.0 0.3 0.1 1.6 m; V 1.87 s[(2.0/1.6) 1] =??= = = ? 111 whence Q V h (1.87)(2.0) .Ans== ? ? 3 m 3.74 sm Chapter 3 ? Integral Relations for a Control Volume 291 3.176 In the spillway flow of Fig. P3.176, the flow is assumed uniform and hydrostatic at sections 1 and 2. If losses are neglected, compute (a) V2 and (b) the force per unit width of the water on the spillway. Solution: For mass conservation, 2112 1 1 5.0 V V h /h V 7.14V 0.7 === Fig. P3.176 (a) Now apply Bernoulli from 1 to 2: 22 2 2 12 1 12 1 VV V pp (7.4V) h h ; or: 0 5.0 0 0.7 2g 2g 2g 2g?? ++?++ ++?+ + 2 1121 2 2(9.81)(5.0 0.7) Solve forV ,orV , V 7.14V . (a) [(7.14) 1] Ans ? ==== ? mm 1.30 9.28 ss (b) To find the force on the spillway (F ?), put a CV around sections 1 and 2 to obtain 22 x1221 F F h h m(V V ), or, using the given data, 22 ? ? ?=?+ ? = ? 22 1 F (9790)[(5.0) (0.7) ] 998[(1.30)(5.0)](9.28 1.30) . (b) 2 Ans=?? ?? N 68300 m 3.177 For the water-channel flow of Fig. P3.177, h1 = 1.5 m, H = 4 m, and V1 = 3 m/s. Neglecting losses and assuming uniform flow at sections 1 and 2, find the downstream depth h2, and show that two realistic solutions are possible. Solution: Combine continuity and Bernoulli between 1 and 2: Fig. P3.177 222 2 121 1 2 21 1 2 2 22 VVV h 3(1.5) (4.5/h ) VV ; hH h 1.54 h h h 2g 2g 2(9.81) 2(9.81) == ++?+= ++? + 292 Solutions Manual ? Fluid Mechanics, Fifth Edition 32 22 Combine into a cubic equation: h 5.959 h 1.032 0. The three roots are:?+= 22 2 h 0.403 m (impossible); h (subcritical); h (supercritical) .Ans =? = = + + 5.93 m 0.432 m 3.178 For the water channel flow of Fig. P3.178, h1 = 0.45 ft, H = 2.2 ft, and V1 = 16 ft/s. Neglecting losses and assuming uniform flow at sections 1 and 2, find the downstream depth h2. Show that two realistic solutions are possible. Solution: The analysis is quite similar to Prob. 3.177 - continuity + Bernoulli: Fig. P3.178 22 2 2 1121 21 1 2 2 22 h 16(0.45) V V V (7.2/h ) V V ; h h H 0.45 h 2.2 h h 2g 2g 2(32.2) 2(32.2) == +=++= += ++ Combine into a cubic equation: 32 22 h 2.225 h 0.805 0?+=. The three roots are: 22 2 h 0.540 ft (impossible); h (subcritical); h (supercritical) Ans. =? = = + + 2.03 ft 0.735 ft 3.179 A cylindrical tank of diameter D contains liquid to an initial height ho. At time t = 0 a small stopper of diameter d is removed from the bottom. Using Bernoulli?s equation with no losses, derive (a) a differential equation for the free-surface height h(t) during draining and (b) an expression for the time to to drain the entire tank. Solution: Write continuity and the unsteady Bernoulli relation from 1 to 2: 22 22 22 11 1 21 2 2 1 VpV pV A D ds gz gz ; Continuity: V V V t2 2 d ? ?? ? ?? +++ =++ = = ?? ?? ? Chapter 3 ? Integral Relations for a Control Volume 293 The integral term 1 VdV ds h tdt ? ? ? ? is very small and will be neglected, and p1 = p2.. Then 12 1 2gh V 1? ?? ? ?? ? ?? , where ? = (D/d) 4 ; but also 1 dh V dt =? , separate and integrate: o 1/2 4ht 1/2 ho dh 2g D dt, or: , (a) 1dh Ans.? ? ?? ???? ?? =? =?? ?? ?? ?? ? ?? ???? ?? ?? 2 1/2 1/2 o g hh t 2( 1) =? ?? (b) the tank is empty when [] = 0 in (a) above, or tfinal = [2(? ? 1)g/ho] 1/2 . Ans. (b) 3.180 The large tank of incompressible liquid in Fig. P3.180 is at rest when, at t = 0, the valve is opened to the atmosphere. Assuming h ? constant (negligible velocities and accelerations in the tank), use the unsteady frictionless Bernoulli equation to derive and solve a differential equation for V(t) in the pipe. Fig. P3.180 Solution: Write unsteady Bernoulli from 1 to 2: 2 22 21 21 1212 1 1 VV V ds gz gz , where p p , V 0, z 0, and z h const t2 2 ? ? ++?+ = ? ? == ? The integral approximately equals dV L, dt so the diff. eqn. is 2 dV 2L V 2gh dt += This first-order ordinary differential equation has an exact solution for V = 0 at t = 0: ?? ?? ?? ,where Ans. final final final Vt V V tanh V 2gh 2L == 3.181 Modify Prob. 3.180 as follows. Let the top of the tank be enclosed and under constant gage pressure po. Repeat the analysis to find V(t) in the pipe. 294 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: The analysis is the same as Prob. 3.180, except that we now have a (constant) surface-pressure term at point 1 which contributes to Vfinal: 2 22 2 oo21 21 1 ppVV V dVV ds gz gz L gh, with V 0 at t 0. t2 2 dt2 ? ?? ? ++?++= +=+ = = ? ?? = ?? ?? The solution is: , where Ans. final o final final Vt 2p V V tanh V 2gh 2L =+ ? 3.182 The incompressible-flow form of Bernoulli?s relation, Eq. (3.77), is accurate only for Mach numbers less than about 0.3. At higher speeds, variable density must be accounted for. The most common assumption for compressible fluids is isentropic flow of an ideal gas, or p = C? k , where k = cp/cv. Substitute this relation into Eq. (3.75), integrate, and eliminate the constant C. Compare your compressible result with Eq. (3.77) and comment. Solution: We are to integrate the differential Bernoulli relation with variable density: kk1 pv pC,sodpkC d,kc/c??? ? === Substitute this into the Bernoulli relation: k1 dp kC d V dV g dz V dV g dz 0 ?? ?? ? + += + += k2 Integrate: kC d V dV g dz 0 constant?? ? ++== ???? The first integral equals kC? k?1 /(k ? 1) = kp/[?(k ? 1)] from the isentropic relation. Thus the compressible isentropic Bernoulli relation can be written in the form Ans. 2 kp V gz constant (k 1) 2 ++= ? ? It looks quite different from the incompressible relation, which only has ?p/?.? It becomes more clear when we make the ideal-gas substitution p/? = RT and cp = kR/(k ? 1). Then we obtain the equivalent of the adiabatic, no-shaft-work energy equation: Ans. 2 p V c T gz constant 2 ++= Chapter 3 ? Integral Relations for a Control Volume 295 3.183 The pump in Fig. P3.183 draws gasoline at 20°C from a reservoir. Pumps are in big trouble if the liquid vaporizes (cavitates) before it enters the pump. (a) Neglecting losses and assuming a flow rate of 65 gal/min, find the limitations on (x, y, z) for avoiding cavitation. (b) If pipe- friction losses are included, what additional limitations might be important? Solution: (a) From Table A.3, ? = 680 kg/ m 3 and pv = 5.51E+4. 12 21 () av p gy ppp zzyz gg ? ?? +?? ?=+= = (100,000 55,100) 6.73 (680)(9.81) y zyzm ? += + = Fig. P3.183 Thus make length z appreciably less than 6.73 (25% less), or z < 5 m. Ans. (a) (b) Total pipe length (x + y + z) restricted by friction losses. Ans. (b) 3.184 For the system of Prob. 3.183, let the pump exhaust gasoline at 65 gal/min to the atmosphere through a 3-cm-diameter opening, with no cavitation, when x = 3 m, y = 2.5 m, and z = 2 m. If the friction head loss is hloss ? 3.7(V 2 /2g), where V is the average velocity in the pipe, estimate the horsepower required to be delivered by the pump. Solution: Since power is a function of hp, Bernoulli is required. Thus calculate the velocity, 3 2 m/s (65 gal/min) 6.3083 5 gal/min 5.8 m/s (0.03 ) 4 E Q V A ? ?? ? ?? ?? == = The pump head may then be found, 2 12 12 2 j fp V pp zzhh g?? += ++?+ 22 100,000 (680)(9.81)(2.5) 100,000 3.7(5.8 ) (5.8 ) 2.5 2 (680)(9.81) (680)(9.81) 2(9.81) 2(9.81) p h + ?= ++ ?+ 296 Solutions Manual ? Fluid Mechanics, Fifth Edition 10.05 p hm= ?==(680)(9.81)(0.0041)(10.05) p PQh Ans.P 275 W 0.37 hp= = 3.185 Water at 20°C flows through a vertical tapered pipe at 163 m 3 /h. The entrance diameter is 12 cm, and the pipe diameter reduces by 3 mm for every 2 meter rise in elevation. For frictionless flow, if the entrance pressure is 400 kPa, at what elevation will the fluid pressure be 100 kPa? Solution: Bernouilli?s relation applies, 22 112 2 12 12 p Qp Q zz gA gA?? ++ = ++ (1) Where, 21 21 d d 0.0015(z z )=? ? (2) Also, Q1 = Q2 = Q = (163 m 3 /h)(h/3600s) = 0.0453 m 3 /s; ? = 9790; z1 = 0.0; p1 = 400,000; and p2 = 100,000. Using EES software to solve equations (1) and (2) simultaneously, the final height is found to be z ? 27.2 m. The pipe diameter at this elevation is d2 = 0.079 m = 7.9 cm. Chapter 3 ? Integral Relations for a Control Volume 297 FUNDAMENTALS OF ENGINEERING EXAM PROBLEMS: Answers FE3.1 In Fig. FE3.1 water exits from a nozzle into atmospheric pressure of 101 kPa. If the flow rate is 160 gal/min, what is the average velocity at section 1? (a) 2.6 m/s (b) 0.81 m/s (c) 93 m/s (d) 23 m/s (e) 1.62 m/s FE3.2 In Fig. FE3.1 water exits from a nozzle into atmospheric pressure of 101 kPa. If the flow rate is 160 gal/min and friction is neglected, what is the gage pressure at section 1? (a) 1.4 kPa (b) 32 kPa (c) 43 kPa (d) 22 kPa (e) 123 kPa FE3.3 In Fig. FE3.1 water exits from a nozzle into atmospheric pressure of 101 kPa. If the exit velocity is V2 = 8 m/s and friction is neglected, what is the axial flange force required to keep the nozzle attached to pipe 1? (a) 11 N (b) 36 N (c) 83 N (d) 123 N (e) 110 N FE3.4 In Fig. FE3.1 water exits from a nozzle into atmospheric pressure of 101 kPa. If the manometer fluid has a specific gravity of 1.6 and h = 66 cm, with friction neglected, what is the average velocity at section 2? (a) 4.55 m/s (b) 2.4 m/s (c) 2.8 m/s (d) 5.55 m/s (e) 3.4 m/s FE3.5 A jet of water 3 cm in diameter strikes normal to a plate as in Fig. FE3.5. If the force required to hold the plate is 23 N, what is the jet velocity? (a) 2.85 m/s (b) 5.7 m/s (c) 8.1 m/s (d) 4.0 m/s (e) 23 m/s FE3.6 A fireboat pump delivers water to a vertical nozzle with a 3:1 diameter ratio, as in Fig. FE3.6. If friction is neglected and the flow rate is 500 gal/min, how high will the outlet water jet rise? (a) 2.0 m (b) 9.8 m (c) 32 m (d) 64 m (e) 98 m FE3.7 A fireboat pump delivers water to a vertical nozzle with a 3:1 diameter ratio, as in Fig. FE3.6. If friction is neglected and the pump increases the pressure at section 1 to 51 kPa (gage), what will be the resulting flow rate? (a) 187 gal/min (b) 199 gal/min (c) 214 gal/min (d) 359 gal/min (e) 141 gal/min FE3.8 A fireboat pump delivers water to a vertical nozzle with a 3:1 diameter ratio, as in Fig. FE3.6. If duct and nozzle friction are neglected and the pump provides 12.3 feet of head to the flow, what will be the outlet flow rate? (a) 85 gal/min (b) 120 gal/min (c) 154 gal/min (d) 217 gal/min (e) 285 gal/min FE3.9 Water flowing in a smooth 6-cm-diameter pipe enters a venturi contraction with a throat diameter of 3 cm. Upstream pressure is 120 kPa. If cavitation occurs in the throat at a flow rate of 155 gal/min, what is the estimated fluid vapor pressure, assuming ideal frictionless flow? (a) 6 kPa (b) 12 kPa (c) 24 kPa (d) 31 kPa (e) 52 kPa FE3.10 Water flowing in a smooth 6-cm-diameter pipe enters a venturi contraction with a throat diameter of 4 cm. Upstream pressure is 120 kPa. If the pressure in the throat is 50 kPa, what is the flow rate, assuming ideal frictionless flow? (a) 7.5 gal/min (b) 236 gal/min (c) 263 gal/min (d) 745 gal/min (e) 1053 gal/min 298 Solutions Manual ? Fluid Mechanics, Fifth Edition Fig. FE3.1 Fig. FE3.5 Fig. FE3.6 Chapter 3 ? Integral Relations for a Control Volume 299 COMPREHENSIVE PROBLEMS C3.1 In a certain industrial process, oil of density ? flows through the inclined pipe in the figure. A U-tube manometer with fluid density ?m, measures the pressure difference between points 1 and 2, as shown. The flow is steady, so that fluids in the U-tube are stationary. (a) Find an analytic expression for p1 ? p2 in terms of system parameters. (b) Discuss the conditions on h necessary for there to be no flow in the pipe. (c) What about flow up, from 1 to 2? (d) What about flow down, from 2 to 1? Solution: (a) Start at 1 and work your way around the U-tube to point 2: 12 21 , : where z z z (a) m pgsgh ghgsgzp or Ans. ? ?? ??++? ???= ?= ? m pp gz gh 12 ()?=?+ ???? (b) If there is no flow, the pressure is entirely hydrostatic, therefore ?p = ?g and, since ?m ? ?, it follows from Ans. (a) above that h = 0 Ans. (b) (c) If h is positive (as in the figure above), p1 is greater than it would be for no flow, because of head losses in the pipe. Thus, if h > 0, flow is up from 1 to 2. Ans. (c) (d) If h is negative, p1 is less than it would be for no flow, because the head losses act against hydrostatics. Thus, if h < 0, flow is down from 2 to 1. Ans. (d) Note that h is a direct measure of flow, regardless of the angle ? of the pipe. C3.2 A rigid tank of volume ? = 1.0 m 3 is initially filled with air at 20°C and po = 100 kPa. At time t = 0, a vacuum pump is turned on and evacuates air at a constant volume flow rate Q = 80 L/min (regardless of the pressure). Assume an ideal gas and an isothermal process. (a) Set up a differential equation for this flow. (b) Solve this equation for t as a function of (?, Q, p, po). (c) Com- pute the time in minutes to pump the tank down to p = 20 kPa. [Hint: Your answer should lie between 15 and 25 minutes.] 300 Solutions Manual ? Fluid Mechanics, Fifth Edition Solution: The control volume encloses the tank, as shown. The CV mass flow relation becomes () 0 out in d dmm dt ??+???= ? Assuming that ? is constant throughout the tank, the integral equals ??, and we obtain 0, : , ln o ddQ Qt Q or dt yielding dt ?? ? ?? ? ??? ?? + = =? =? ?? ?? ?? Where ?o is the initial density. But, for an isothermal ideal gas, ?/?o = p/po. Thus the time required to pump the tank down to pressure p is given by ?? ?? ?? (a, b)Ans. o p t Qp =? ? ln (c) For our particular numbers, noting Q = 80 L/min = 0.080 m 3 /min, the time to pump a 1 m 3 tank down from 100 to 20 kPa is 3 3 1.0 m 20 ln (c) 1000.08 m /min tAns. ?? =? = ?? ?? 20.1 min C3.3 Suppose the same steady water jet as in Prob. 3.40 (jet velocity 8 m/s and jet diameter 10 cm) impinges instead on a cup cavity as shown in the figure. The water is turned 180° and exits, due to friction, at lower velocity, Ve = 4 m/s. (Looking from the left, the exit jet is a circular annulus of outer radius R and thickness h, flowing toward the viewer.) The cup has a radius of curvature of 25 cm. Find (a) the thickness h of the exit jet, and (b) the force F required to hold the cupped object in place. (c) Compare Fig. C3.3 part (b) to Prob. 3.40, where F = 500 N, and give a physical explanation as to why F has changed. Solution: For a steady-flow control volume enclosing the block and cutting through the jets, we obtain ?Qin = ?Qout, or: ? ?=?? 22 2 [()],: (a) 4 jje VDVR Rh or Ans. jj e VD hR R V =? ? 2 2 4 Chapter 3 ? Integral Relations for a Control Volume 301 For our particular numbers, 2 2 8(0.1) 0.25 (0.25) 0.25 0.2398 0.0102 m (a) 44 hAns.=? ? =? = =1.02 cm (b) Use the momentum relation, assuming no net pressure force except for F: ?=?= ?? () (), : (b) x jet e jet j FFmVmVor Ans. jjje FVDVV=+ ? ? 2 () 4 For our particular numbers: 2 998(8) (0.1) (8 4) (b) 4 FA ? =+=752 N to the left (c) The answer to Prob. 3.40 was 502 N. We get 50% more because we turned through 180°, not 90°. Ans. (c) C3.4 The air flow beneath an air hockey puck is very complex, especially since the air jets from the table impinge on the puck at various points asymmetrically. A reasonable approximation is that, at any given time, the gage pressure on the bottom of the puck is halfway between zero (atmospheric) and the stagnation pressure of the impinging jets, po = 1/2 ?Vjet 2 . (a) Find the velocity Vjet required to support a puck of weight W and diameter d, with air density ? as a parameter. (b) For W = 0.05 lbf and d = 2.5 inches, estimate the required jet velocity in ft/s. Solution: (a) The puck has atmospheric pressure on the top and slightly higher on the bottom: ?? ?? ?==+ ?? ?? 22 1 () 0 , . (a) 22 4 under a puck jet p p A W V d Solve for Ans jet W V d = 4 ?? For our particular numbers, W = 0.05 lbf and d = 2.5 inches, we assume sea-level air, ? = 0.00237 slug/ft 3 , and obtain 3 40.05 lbf . (b) (2.5/12 ft) (0.00237 slug/ft ) jet VAns ? ==50 ft/s 302 Solutions Manual ? Fluid Mechanics, Fifth Edition C3.5 Neglecting friction sometimes leads to odd results. You are asked to analyze and discuss the following example in Fig. C3.5. A fan blows air vertically through a duct from section 1 to section 2, as shown. Assume constant air density ?. Neglecting frictional losses, find a relation between the required fan head hp and the flow rate and the elevation change. Then explain what may be an unexpected result. Solution: Neglecting frictional losses, hf = 0, and Bernoulli becomes, 22 11 2 2 12p pV p V zzh gg g g?? ++=++? Fig. C3.5 22 11 2 12 2 12 () p pV p gzz V zzh gg g g ? ?? +? ++= ++? Since the fan draws from and exhausts to atmosphere, V1 = V2 ? 0. Solving for hp, Ans. p h g z z gz gz= ?+ ? =? ?? 12 2 1 () 0 Without friction, and with V1 = V2, the energy equation predicts that hp = 0! Because the air has insignificant weight, as compared to a heavier fluid such as water, the power input required to lift the air is also negligible. icci Chapter 3 € Integral Relations

Back

Next

About this note

Author: Anonymous

Textbook: Fluid Mechanics

Created: 2009-04-28

Updated: 2009-04-28

File Size: 0 page(s)

Keywords: flash card flashcards digital flashcards note sharing notes textbook wiki college dorm class classroom exam homework test quiz university college education learn student teachers tutors share, study blue studyblue studyblu

Views: 665

Textbook: Fluid Mechanics

Created: 2009-04-28

Updated: 2009-04-28

File Size: 0 page(s)

Keywords: flash card flashcards digital flashcards note sharing notes textbook wiki college dorm class classroom exam homework test quiz university college education learn student teachers tutors share, study blue studyblue studyblu

Views: 665

Simply amazing. The flashcards are smooth, there are
many different types of
studying tools, and there is
a great search engine. I praise
you on the awesomeness.
- Dennis

I have been getting MUCH
better grades on all my tests
for school. Flash cards, notes,
and quizzes are great on here.
Thanks!
- Kathy

I was destroying whole rain forests with my flashcard production, but YOU, StudyBlue, have saved the ozone layer. The earth thanks you.
- Lindsey

This is the greatest app on my phone!! Thanks so much for making it easier to study. This has helped me a lot!
- Tyson

© 2014 StudyBlue Inc. All rights reserved.